Jump to content
SAU Community

Recommended Posts

  • Replies 63
  • Created
  • Last Reply

Top Posters In This Topic

Has the car ever had frontal damage that might affect the axles etc? If not then I might be interested in the whole front axle with wishbones etc.

Oh and the speedometer cable as well... definitely need that.

No front end damage from what I can tell, mainly driver side and roof, from people standing on it not from rolling.

I may need the speedo cable as I planning on using all the bits from the R32 to convert my Cef to five speed, gunna use the R32's donk aswell. Or are cefs electric speedo?

dunno... i'll let you know when I take my ceffie apart :cheers: which should be soon as I'm putting a laure C33 dash in.

If you don't need the cable, then let me know via PM or email [email protected]

Do you have this piece of plastic? It sits under the top of the bonnet (near the windscreen), under the wipers:

windscreen-part.png

Also after the centre console rear ashtray (don't smoke, just looks weird having a hole) :D

Cheers,

Lucien.

Not sure on the rear windscreen moulding. Its a fscker to get off without damaging it so I might be better off just buying a new one (and being raped by Nissan) unless yours is already off and in good condition :D ... ?

Lucien.

Mine is probably pretty sun dried by now, Ill see how i go getting it out.

Heh. Good luck. It was a bastard on mine. 15 year old silicon (and stacks of it) didn't want to give :)

Lemme know how much you want for the rear ashtray.

LW.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
    • Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • also possibly backed up to my filler and shat down it! 🤣
    • Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
×
×
  • Create New...