Jump to content
SAU Community

Recommended Posts

For the hypothetical argument:-

For the ignition timing, I think that you would need a dpa to intercept each spark plug. Thats if that is how they work.

That's 6 bulky shithouselooking cream boxes that you would have trouble hiding in the non existent room behind the dash. The idea is good, but I think if you had to buy 6, the cost would be similar to a unichip.

Or maybe I'm looking at it the wrong way, are you saying that you intecept the signal from the CAS? That may work...

Or something else that the ECU uses to calculate the ignition timing.

Unfortunatley, I don't know enough about CAS signals or format. Maybe someone else could enlighten.

The real answer is stop fuggin around and get a PFC.

I think that basicly, if you want to do more than bend the AFM voltage, then a PFC is the way to go as it can give you control over everything. Easy to fit, better tuning results and less ugly plastic boxes to hide.

I do know that they can be used to do a speedo correction.

You might be able to use them to fool the speed limiter.

There is probably a 101 uses for them, all limited by you imagination.

  • Replies 1k
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Ok I'm going to have to jump in the middle of your convo here...

Well I thought the IEBC was working for me, but turns out, it doesnt work at all! I cannot make it go higher or lower than 7-8 psi no matter what setting I put in. Anyone know what's going on?

The real answer is stop fuggin around and get a PFC.

I think that basicly, if you want to do more than bend the AFM voltage, then a PFC is the way to go as it can give you control over everything. Easy to fit, better tuning results and less ugly plastic boxes to hide.

Unfortunately, it ain't that easy - there isn't a PowerFC available that is a direct plug-in to the Stagea wiring loom (this is that Stagea section of the forums, after all).

Getting one to work involves, amongst other things, converting your Stagea to manual (none of the series 1 RB25-engined Stageas were manual, and there are no PFC's for auto Skylines), hacking up the Stagea wiring loom to suit the PowerFC (or vice-versa), and sorting out an alternative method to keep the ATESSA control - most of the Stageas that come into the country are AWD, and there were no RB25DET-engined Skylines that also had the ATESSA system.

For the hypothetical argument:-

For the ignition timing, I think that you would need a dpa to intercept each spark plug. Thats if that is how they work.

That's 6 bulky shithouselooking cream boxes that you would have trouble hiding in the non existent room behind the dash. The idea is good, but I think if you had to buy 6, the cost would be similar to a unichip.

Or maybe I'm looking at it the wrong way, are you saying that you intecept the signal from the CAS? That may work...

Or something else that the ECU uses to calculate the ignition timing.

Unfortunatley, I don't know enough about CAS signals or format. Maybe someone else could enlighten.

The real answer is stop fuggin around and get a PFC.

I think that basicly, if you want to do more than bend the AFM voltage, then a PFC is the way to go as it can give you control over everything. Easy to fit, better tuning results and less ugly plastic boxes to hide.

I do know that they can be used to do a speedo correction.

You might be able to use them to fool the speed limiter.

There is probably a 101 uses for them, all limited by you imagination.

The Apexi SITC changes the CAS signal at 5 rpm points, with interpolation between them. So you achieve the timing that you want. This thread covers fitting an SITC to a Stagea;

http://www.skylinesaustralia.com/forums/in...showtopic=80642

:) cheers :rofl:

Unfortunately, it ain't that easy - there isn't a PowerFC available that is a direct plug-in to the Stagea wiring loom (this is that Stagea section of the forums, after all).

Getting one to work involves, amongst other things, converting your Stagea to manual (none of the series 1 RB25-engined Stageas were manual, and there are no PFC's for auto Skylines), hacking up the Stagea wiring loom to suit the PowerFC (or vice-versa), and sorting out an alternative method to keep the ATESSA control - most of the Stageas that come into the country are AWD, and there were no RB25DET-engined Skylines that also had the ATESSA system.

I'd agree with that. But like SK has pointed out - there are better options for timing.

I guess I overlooked the whole stagea thing as I have a manual skyline...

The fact that SK couldn't put in a PFC is the major reason this thread was started hey!

ive fried two IEBC's by switching too slowly from high to low, kinda staying in between.

It caused heat to build up in one of the resitors and it to burn out. I replaced it but never worked again. The result was the EBC being stuck on load point 64. Basically making it as good as a bleed valve :)

The Apexi SITC changes the CAS signal at 5 rpm points, with interpolation between them. So you achieve the timing that you want. This thread covers fitting an SITC to a Stagea;

http://www.skylinesaustralia.com/forums/in...showtopic=80642

:) cheers :rolleyes:

So you could use a DFA to change the signal from the CAS? and it would probably work better than the SITC as it has more resolution?

Just throwing around a few ideas... At the moment Ive got the DFA and IEBC and a Universal Voltage Switch kit running an intercooler water spray... could add another beige box. ;-)

Hey, I just found out something.

I have a DFA and lately on cold nights, I have been loosing power between 5000rpm and 7000rpm,and going through more fuel.

Plugged in the controller and found that the input was 1 and the output 0. SO I pulled it apart and found the red led wasn't on. The "switch in" was not working. I had to adjust VR4 to get it to switch on when the engine turned over. And now the red light comes on.

So I'm not sure how this happened. Maybe vibrations caused VR4 to unscrew changing the resistance, or maybe it's because I changed batteries and the alernator doesn't charge the battery as vigourously anymore (the old one was fooked). Anyway, just thought I'd share.

  • 2 weeks later...

Help!!!! I have a standard R33 boost control solonoid and an Apexi 3 port boost control solonoid.

1. Which one will be better to use?

2. Will the Apexi item flow better with more control due to its larger ports?

3. How do you set The 3 port up? Obviously you put the two barbs to COM (in) and NC (out) but what do you do with the NO port?

4. Is there anything else required to change the setup of the solonoid to NC operation fom NO?

Cheers in advance :)

NO = Normally Open

NC = Normally Closed

These are the two states of the outputs when the solenoid is NOT energized.

COM = Common Input

For this application it's best to use a NC, as for the vast majority of the time (when you're OFF boost) you want the valve shut, then when you're holding back the boost it opens up. This is so you're pulsing the solenoid as little as possible, and avoiding holding it open for a long time, which can shorten its life-span.

In the case of bleed systems, you'd want a normally open valve, coz it'll spend most of it's time open.

The APEXI one in question obviously has both, useful, but overkill for this.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...