Jump to content
SAU Community

Recommended Posts

Hey guyz

Finally got my 32 on the road and have noticed that in sum gears it seems to lag.

Now im not to sure whether becoz it was sitting in japan for 5mnths without being driven and when it arrived it had no fuel at all so possible sum shit is blocking the injectors but yeh not running the best

The engine is a stock rb20.. no other visible modifications.

Not sure wat psi its running either..

When you punch 1st and 2nd gear the car seems to respond particularly well.. however when your just crawling and then put ur foot on the gas say when ur in 2nd there is a short wait b4 the car decides to move, same with 3rd gear too

Seems to me like its missing...

Um any suggestions?

Thanks Joe!

Link to comment
https://www.sau.com.au/forums/topic/61357-r32-laggin-probs/
Share on other sites

Hey guyz

Finally got my 32 on the road and have noticed that in sum gears it seems to lag.

Now im not to sure whether becoz it was sitting in japan for 5mnths without being driven and when it arrived it had no fuel at all so possible sum shit is blocking the injectors but yeh not running the best

The engine is a stock rb20.. no other visible modifications.

Not sure wat psi its running either..

When you punch 1st and 2nd gear the car seems to respond particularly well.. however when your just crawling and then put ur foot on the gas say when ur in 2nd there is a short wait b4 the car decides to move, same with 3rd gear too

Seems to me like its missing...

Um any suggestions?

Thanks Joe!

They don't have much low down torque you need to keep it up in the rev range a bit, between shift changes do you:

* Clutch in, change gear, clutch out, THEN get on the gas,

OR

* Clutch in, change gear, get on the gas and clutch out as the revs are rising?

You need to be doing the latter, after having driven a V6 auto commo for the 3 years prior to getting my skyline it took me a little while to get out of habit of just putting the foot down and expecting something to happen, I'd just put it in to gear then put the foot down and it reacted very sluggishly just as you're describing. But maybe that was just me. :D

Link to comment
https://www.sau.com.au/forums/topic/61357-r32-laggin-probs/#findComment-1159275
Share on other sites

Also try the computer reset trick, first go grab a tank full of BP Ultimate (any 98RON will do but i like BP) and take your car home, disconnect the negative from the battery, hold the brake pedal down for a min, then reconnect the battery and take her for a thrash.

This all puts the ECU back in to self learn mode making slight adjustments to ignition.

If you eliminate you shift habits, fuel quality, ECU reset as possible causes the next step is to check the timing.

Link to comment
https://www.sau.com.au/forums/topic/61357-r32-laggin-probs/#findComment-1159335
Share on other sites

i think they are laggy, but not as bad as everyone makes out.....with an exhaust, cam gears and hi flow panel filter it made a world of difference......on and off boost, your not gonna take on a rb25 or rb30 and beat it down low but they go well for that they are.

my 2cents

Link to comment
https://www.sau.com.au/forums/topic/61357-r32-laggin-probs/#findComment-1160300
Share on other sites

Now think how fun it would be on the street with a decent turbo trying to make over 200rwkw. :(

You do get used to it and adjust your driving style. :D

Yogi is right.. The ol' RB20DET does go really well with a few mods for what they are. I was impressed with how well mine was.

Once on boost they rev nicely and do go well. Launching is another story. Mine would bog down with anything under 4000-4200rpm on board.

Link to comment
https://www.sau.com.au/forums/topic/61357-r32-laggin-probs/#findComment-1161259
Share on other sites

mine was a bit like that too and I had, filter,full 3" exhaust, FMIC,1.0Bar boost etc...

I think its just the engines nature man

take it out to the track for the day and have a chance to run around without breaking the law and get used to the car would be my advice. I did everytime I added some mods and it helped

mark

Link to comment
https://www.sau.com.au/forums/topic/61357-r32-laggin-probs/#findComment-1161411
Share on other sites

Throw the exhaust and cat in the bin, get a new system, get a Hybrid FMIC, and throw in a new fuel pump. Combined with a good service with fresh fluids and your pocket will be $2,000 lighter...

The difference will be huge. You will have about 150-160rwkws and a in that state the engine can be flogged repeatedly for years and another 50-80,000kms:)

I wouldnt really bother with a boost controller as you will find you will make around 12-13psi anyway with the breathing mods.

Yeh they can be a little breathless, but ppl, they are a 1400kg 2.0L turbo car. I love ringing the RB20s neck, it feels sporty:) Half the fun of turbo cars is the rush onto boost.:)

Link to comment
https://www.sau.com.au/forums/topic/61357-r32-laggin-probs/#findComment-1161900
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I dunno about that as a blanket statement. Pitwork is Nissan's "Nissan genuine" thing, and for stuff like timing belts, I have found them to be excellent. Of course, for things like oil filters, you always use proper trusted brands anyway, not whatever the OEM has taken to using.
    • Ahhhh... If you were putting 12V to the led in there, that's likely made it very unhappy. Chances are how you put power, was 12V across an LED that's meant to only have about 20mA through it at peak, and a forward voltage of about 1.8 to 2.4 volts. That circuit is likely only a 3V3 circuit, and will have a resistor in series with the led too. That's my guesstimate on that light, without having touched one.
    • Another vote for installing them and see how you go.  I mean, you already own them, why would you not fit them? 
    • I have had too many of those over the years, my cars have a toolkit or at minimum a cheapy multi tool thing because its too easy to be snookered by some stupid plastic clip that stops you checking the battery terminal isn't loose.
    • Basically, if there is a part# on the nissan catalogue, it is a genuine part. There is a thing called "new old stock" which is stuff made years ago but never sold (or landfilled), but it is super hit and miss what you can buy. Other than some expensive Nismo stuff there is nothing new being made that suits these cars. The only time to be a little careful is (mostly in the US I think, but maybe Japan too), Nissan started rebranding some cheap crap maintenance parts like oil filters as "Pitworks"; stay away from them, if you are buying cheap just buy whatever the local car parts shop carries The three part numbers have an explanation on Amayama: 0V005 is auto, base style 0V015 is manual 0V505 is auto, hectic momo branded ones, maximum F&F points there!
×
×
  • Create New...