Jump to content
SAU Community

Recommended Posts

Hey guys i recently had a system installd by GL pro sound

Got put in 2 12"inch rockford fosgates, splits at the front and 2 rockford amps

Now my boot rattles like hell

GL pro sound tell me u cannot get rid of the rattle

Is there any way i can reduce the rattle or eliminate it totally??

Id appreciate the help,

Thanx :D

Link to comment
https://www.sau.com.au/forums/topic/63241-boot-rattle/
Share on other sites

Check your number plate, that usually makes the most noise.

You can sound deaden the under side of your boot lid. Check all screws/bolts are tight. Check the jack and tool kit, they will make some noise!

If your bootlid rattles, try looking for a thicker rubber seal so you almost haveto forceit shut.

They are wrong, there is alot you can do :D

Hope that helps!

Link to comment
https://www.sau.com.au/forums/topic/63241-boot-rattle/#findComment-1190470
Share on other sites

$110ish for a sheet of quality sound deadening like serenity max.

while you are at it, buy 2 and deaden both doors.

tighten every nut and bolt you can get a screwdriver or spanner onto.

tighten the jack as previously suggested.

if you are superkeen pull the back seats out and replace the parcel tray with mdf.

and if you are superdooper keen install sound deadening under the back seat.

you should have Nissan Skyline R33 Infiniti after all this.

Link to comment
https://www.sau.com.au/forums/topic/63241-boot-rattle/#findComment-1192595
Share on other sites

glps really said you can't do anything to fix the rattles???!!!! surely not. boot rattles are pretty much par for the course with a decent system w/o sound deadening in most cars and i'd imagine most shops are well aware of this.

whats rattling (if is the bootlid) is the frame. get some non-acitic silicone (otherwise it'll corrode) and run a bead between the outer "skin" and the framing. go nuts and do it properly. what you want to achieve is to isolate the two from each other. then you want to cover the whole of your bootlid underside in a good quality sound deadener (g-spot is the one to go with) and re-carpet it.

if you don't want to do it yourself, you should have a chat to marty @ fhrx studios. he's on these forums and based in sydney. shoot him a pm. he's deadened many a japper (inc his own s15) and knows the ins and outs.

d

Link to comment
https://www.sau.com.au/forums/topic/63241-boot-rattle/#findComment-1203758
Share on other sites

  • 1 month later...

GL Pro Sould are pros, i carnt beleive they told you that .. yes as everyone has told you sound deaden everything .. you used to be able to buy this stuff called SOUND OFF professional damping for high performance car audio, you could buy this stuff in brush on and in sheets. You need to do the inside of your rear quarter panels and the boot lid, run some seam sealer in all the seams of the re-enforcements on you boot lid and either brush the deadner on the whold underside of your boot or cut out a sound deadner sheet and glue it on .. i would recomend using the brush on stuff instead of the matting.. its amazing what a difference it makes ..

Link to comment
https://www.sau.com.au/forums/topic/63241-boot-rattle/#findComment-1269262
Share on other sites

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • also possibly backed up to my filler and shat down it! 🤣
    • Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
    • What sold me on Trailer Park Boys is this scene: Great stuff, just stay clear from the new Netflix production.
×
×
  • Create New...