Jump to content
SAU Community

Recommended Posts

Hey everyone,

i few of the sauwa members where asking about buying some sauwa seat-covers. Now i have took on the job of getting it done and stuff. At the moment we arn't sure of the design but the cover will be similar to the snap-on design (just throw over ur seat and is a bigger fit (if u get me) it would be made in different colours (red,black,blue,purple etc etc) with the sauwa logo in the middle or something similar

Im just after how many people would like to buy it, im going to do it even if its only a few members (so far its me and MirkZ) but i guess the more numbers the less the cost.

So just post if u want some and and ideas of design etc etc

cheers Michael :D

Link to comment
https://www.sau.com.au/forums/topic/63966-eoi-sauwa-seat-covers/
Share on other sites

IMO I think they look pretty tatty/raggy for a car like ours....

Normal seat covers - yes, they look shit on any car, but the Snap-on sort of ones are just when you're dirty or whatever and don't want to get your seats all dirty. Some people like to have them on all the time for some reason...kinda stupid.

The Stahlwille ones go for $45, I was going to get one of them next week (****in plastic disposeable ones are pissin me off :P ) but might wait for these to be made up see how they look...

Ok guys good responds thats good :P

Ok i have a few ideas of designs, it would have the sauwa logo and then possable add a nice pic of a anime r32 gtr or something similar and possable a different design for the passagers seat.

any comments are welcome also ideas :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...