Jump to content
SAU Community

Recommended Posts

HAHHAHAAHHA go check out his cardomain page http://www.cardomain.com/memberpage/777775

and look at the results from his stupid question of turbos vs V8 and TURBOS are killing him in the results ahhahaha

OH another thing he's babbling so much about a 5.7L car putting out high 11s and Perth has got 2.6Ltr cars putting out low 10's hahaha hell go hunt down Cypher in Myaree their 2L RX3 can go down the qrt in low 9's.

  • Replies 350
  • Created
  • Last Reply

Top Posters In This Topic

lol who cares.

in the end who the shit pays over $50k for a ford or holden? heh

if you want to pay.. pay... go drive it instead of posting on forums.

and if i could afford the petrol i'd have my 351 '69 XW GT back on the road.

horses for courses

hey also go hunt down the car MESMERIZE its abit closer to your engine litre, its a twin turbo Soarer that does low 11 on street tyres. and you can't miss the car its got a full Haleqain paint job.

anyone else in perth can recommend this fool some 10sec GTRs to do and try is wang at.

i work as a mechanic at a holden dealership and get to drive cars like yours which i would give a bit of credit if you wernt so up your self. i drive a commodore and a turbo civic and would choose a GTR over your car anyday but not cause i dont like your car but because a GTR would make your car handle like a barina. And whats your user name on street commodores forum?

hey also go hunt down the car MESMERIZE its abit closer to your engine litre, its a twin turbo Soarer that does low 11 on street tyres. and you can't miss the car its got a full Haleqain paint job.

anyone else in perth can recommend this fool some 10sec GTRs to do and try is wang at.

http://www.skylinesaustralia.com/forums/sh...ighlight=ND4SPD

Oh another thing SkylineKiller since you like to read MOTOR mag, check out the Nov/Dec 2003 edition of which STOCK cars can actually hit 300kmhs not cause their speedos say it.

the Lamborghini Murcielago got 301 and who topped the list???..... a $40K R33 GTR STOCK that hit 305 and 306 kmh in its 2 alloted tries.

3 HSV cars were in it and none of them got close. The closest was a $120K yes $120K 1200kg CSV Mondo what pumps 375Kw Stock and it only got to about 280kmh so whats the point when its speedo says 320kmh top speed. Typical HOLDEN theoretic nonsence. Least FORD enthusiasts people are more clued on to what's happening in the car scene.

Guest
This topic is now closed to further replies.



  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...