Jump to content
SAU Community

Fuel Pressure Regulators


Recommended Posts

Hi all,

Was wondering, people state that when you start modifying your engine, you should get a rising rate fuel pressure regulator or something like that. How does this help? Is this something only moderate/heavy modified engines should have or will it give gains on any engine regardless of state of tune?

Cheers!

:P

Link to comment
Share on other sites

The skylines run really rich right.

Say 10 parts air to 1 part fuel

On a mildly modified engine u can use this adjustable reg to wind the overall pressure down when on boost so that your mixtures can come back to say 12:1 more power more fuel economy :P

On a higher modified car u can use it to bump up the pressure to make your injectors squirt more so u can delay having to buy bigger units..Also a bigger fuelpump sometimes requires u to use a reg.

cheers

Link to comment
Share on other sites

I may be wrong here, but I understood that a rising rate reg did the opposite.

A factory reg runs a 1:1 ratio between boost and fuel pressure, so for each psi of boost, the regulator increases the fuel pressure by 1 psi.

A rising rate reg runs 1:1-and-a-bit boost:fuel pressure, so for each psi of boost, the regulator increases the fuel pressure by say 1.1 psi. At higher fuel pressures, more fuel is injected at a given injector duty cycle. This is to stop the A/F leaning off at high boost levels.

The advantage of rising rate reg is that they can be adjusted to give a different-from-factory base fuel pressure, say 45 psi at idle instead of 40psi at idle. This is a cheaper way than fitting a set of higher capacity injectors.

Link to comment
Share on other sites

I actually realised that after I posted. Because you can adjust the pressure, you can reduce as well as increase the base pressure. Therefore you could effectively lean off the mixtures a bit (on a dyno of course!) by reducing the base pressure.

Link to comment
Share on other sites

Originally posted by SeriesIIGTST

Hi all,

How does this help? Is this something only moderate/heavy modified engines should have or will it give gains on any engine regardless of state of tune?

Cheers!

:D

I'll give you a straight answer to your question.

You will need a rising rate regulator if your car is producing over 215kw at the wheels.

- this is when your injectors Duty Cycle are maxed out, ie cannot supply any more fuel.

Also note that the standard fuel 'pumps' are only good for about 200 at the wheels max, and are not known for their reliability.

All you need to know about the regulator is that it can raise the fuel pressure so that when your injectors are OPEN, more fuel will come out due to the higher pressure.

You wont get any gains on a standard engine. Gains will only be realised if your injectors are too small to supply the required amount of fuel (which is around the 215rwkw mark).

just beautiful! :D

Link to comment
Share on other sites

One very large point worth considering if you intend to push the stock injectors with high base pressure:

* As you increase pressure your fuel pump's maximum flow decreases.

This means if you want to wring every last bit out of the stock injectors with a rising rate you had better have the big ass 044 bosch or something similar. Some of the 900 series bosch intank pumps would be pushed very hard to supply the necessay fuel at the high pressures you need for stock injectors to get 230+rwkw.

This is an example of pressure Vs flow for the big bosch.

kgf/cm2 Flow (L/hr)

2 ------------------249

3 ----------------- 236

4 ---------------- 224

5 -------------- 206

6 ----------- 195

Link to comment
Share on other sites

Originally posted by Clint32

Do you think the stock regulator will be ok to use with 550cc injectors and a 044 pump.  The injectors will have plent of spare duty cycle so it should be ok im thinking, wanting about 240rwkw.

That should be fine, 550's (6 of) are roughly 550hp worth at the same pressure. you can get a reg later if you need to.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • RB26 JE pistons to suit 2.8 stroker crank 77.7mm and 86.5mm bore Custom made with EN plating and Je perfect skirt.  Valve pockets Suits 1mm over valves biggest lift you can throw at them. 21mm 210” wall 9310 upgraded wrist pins to suit standard sized 121.5mm rods. I had these made for my build but block had to be rebored to a larger size so sadly I can no longer use them. I spent a-lot of time and money on these pistons.  See photos these are the Heavy duty forging in 2618 material with all the bells and whistles accumulator grooves double force fed pin oilers skirt milling window milling etc.  The En plating was done to the whole piston this helps with heat and also critically in the ring grooves to prevent ring micro welding. The Perfect skirt is JE's propriety coating its a permanent coating that expands and contracts with the bore to prevent piston slap and noise and also friction. you can look these features up.  They have been balanced to a tenth of a gram at my expense. They come with Gas nitrided ring pack's and oil ring rail supports all brand new never used. The Dome volume is 17.9 cc which based on your Gasket thickness and chamber volume can put you anywhere you like in terms of Comp ratio in my case it was just under 9:1 but this is highly customizable for your build.  In terms of sizing these pistons will work with any 77.7mm build using the normal sized rods.  I did buy an extra set of rings at the time of purchase incase i stuffed one up during gapping so i will throw these in at my expense. I purchased these through performance wholesale in Brisbane and still have the receipt if you were to make these now it would cost more then double what i have them listed for. I am super fussy when it comes to building motors so you will see they have been measured and numbered with marker in the photos. Every thing has been handled and stored with the utmost care and diligence. looking for 2350 ONO any question please ask. test is better 0450 428 895 they will be sent via registered post anywhere in Aus free international buyers contact for quote.  
    • Ok that makes sense, I was circling around the idea that this kind of wear would only occur with too long intervals between oil changes but I see what you're saying about the cause being something else.
    • That's perhaps not even correct in this instance though. If the OP were in fact to bin all that troublesome crap and convert to DBW, and then if the problem persisted, we would at least know that it was not caused by any of that troublesome crap and he could go looking for it in more likely places. AND... he would have a significant upgrade in niceness to go along with it!
    • What has an oil change got to do with whether wear is occurring or not? Wear may be facilitated by oil having been left in too long and broken down - but it is far more likely to be a mechanical issue (ie, pressure). The thing with the tested oil being only 5000kms old makes it perhaps equally likely to be lead from bearings or lead from the additive.
    • I had a thought. I still haven't confirmed what additive was used but, the oil from this analysis was only 5,000 k's old and I believe was Mobil 1. Given that the oil was good and fresh, would there still be wear in the engine? What I'm trying to articulate is, I understand that internal wear will happen with incorrect viscosity or not changing oil enough (and maybe other reasons also). But would the wear continue to occur when the oil is changed? Surely it would stop wearing, ie the damage was done? If thats the case, could this suggest maybe that the lead count is not wear? I dont know if that makes sense. It does in my head.
×
×
  • Create New...