Jump to content
SAU Community

Recommended Posts

  • Replies 172
  • Created
  • Last Reply

Top Posters In This Topic

Mate

Could be interested in a cooler & kit for my r33. Mines a Series 11. Have you ordered enough to put one aside for me or have I missed out? Sorry about the late notice as I have only just discovered the world of Skylines! I'm based on the Sunshine Coast so I would come down and pay for it straight away. Can you recommend any one who could fit? I'll end up chopping of an arm. Me and powertools = hospital.

TOY 33: you have PM

Spoke to the manufacturer today. Payment has been recieved an the kits will be shipped on wednesday :cheers: Expect them to be in brisbane 20 days later. Here is the list of kits on there way.

list:

1 - s14 piping kit

4 - s13 piping kits

7 - R33 piping kits

6 - R32 piping kits

1 - PULSAR N14 GTiR

1 - 180SX 2.0L

If you interested there are spare R33, R32 and s13 kits.

OK can confirm the piping kits for a 33 do fit a 32. Takes a little bit of work and some planning but it all fits in. Took me about 6 hours to do all of it and clean it all up. cutting the reinforcing and everything

Any pictures mate? Pictures speak a thousand words....

Thanks

Yeah had to cut the blades. Still need to trim them a bit more but will do it on the weekend. I haven't driven the car since doing it as I need to get the front bar sprayed up and don't want to cut my original bar just for it to come off in a few weeks. Will just leave the car sitting at home until all is ready to go on.

why not just drive withour ur front bar and stick ur numberplate on some where?

Not to stressed by it. I'll take it for a test drive but want to keep it off the road until all the kit is resprayed and the new front bar is ready.

St5ll have an EBC to install

It has been a little while since I posted something in this thread. So I think I should post something. Kits are still sailing! If they are on time they should be here in within a week.

if anyone is intetrested in a kit let me know. Pictures will be posted as sson as the kits arrive

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...