Jump to content
SAU Community

Recommended Posts

Why would you even be driving it if you thought it had blown a turbo wheel off?

They actually do still produce boost pressure with only one turbo working, it's just very low as it is leaking boost ( a lot) but because the gap where the air excapes around the blown turbo compressor wheel is so small, it can still build some pressure.

Quite often (and I know not too many people have experience with this) a blown ceramic turbo will actually kill your entire engine.

We stripped mine down and rebuilt it about 600kms after the turbo blew (and fitting 2530's) and there was no ceramic contamination of the internals what so ever.

Ive heard stories of it happening, but have only seen one person on these forums that has said and stuck by his story that it happened. Maybe we should get Myth Busters onto it? :rofl:

my car was idling really rough today and there was alot of smoke. I removed the o2 sensor where dump pipe was and noticed alot of white smoke coming out. Does this mean the turbo is dead. If this is the case, i still dont understand the rough idle. any ideas?

because most people hear a bang and take thier foot of the accelerator - first thing most people would do... so theres a chance of some bits of exaust wheel falling back into the engine?

I've been told if i ever hear a bang to keep my foot on the gas for another 5seconds to hopefully push all that shit away from inside the engine. I think it would be hard to do - keep your foot down after you hear a bang :P

myth busters.. lol .. I would have thought even if there was ceramic on the piston crowns, it wouldn't take long before it was blasted into powder anyhow.

It's probably correct though, that when you think about it, the turbo is 95% likely to blow the turbo whilst under the foot under full boost.. blowing it out the exhaust, rather than back up the intake.

RB 26 engine shave serperate exhaust manifolds for the front and rear banks of three cylinders.

Say the rear turbo goes, there is a fair amount of time when no gas is exiting the rear three cylinders. In fact, exhaust gas from the front three cylinders will help to push the ceramic pieces into the rear three chambers.

The fact that the exhaust valves are still open while the piston is on the way down also helps to suck the particles in.

myth busters.. lol .. I would have thought even if there was ceramic on the piston crowns, it wouldn't take long before it was blasted into powder anyhow.  

It's probably correct though, that when you think about it, the turbo is 95% likely to blow the turbo whilst under the foot under full boost.. blowing it out the exhaust, rather than back up the intake.

I've thought about this too, and I reckon that a turbo is most likely to blow as you lift off to shift gears. think about this, you are on full throttle, 6500rpm in 3rd, turbo is making 1.1bar boost, as you lift off, there is temporarily a restriction in front of the compressor (before the bovs react) that trys to slow down the compressor and by extension the exhaust wheel, but at this moment there is a huge amount of exhaust gas trying to still make boost.

all theory though :D

but I agree, someone should call myth busters.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Mixing things up - installed some leather recaros to match the leather seat covered rear seats. Interior looks pretty schmick now except for some slight wear on the steering wheel which I will monitor and address if it becomes worse or actually noticeable!  
    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
×
×
  • Create New...