Jump to content
SAU Community

Recommended Posts

Why would you even be driving it if you thought it had blown a turbo wheel off?

They actually do still produce boost pressure with only one turbo working, it's just very low as it is leaking boost ( a lot) but because the gap where the air excapes around the blown turbo compressor wheel is so small, it can still build some pressure.

Quite often (and I know not too many people have experience with this) a blown ceramic turbo will actually kill your entire engine.

We stripped mine down and rebuilt it about 600kms after the turbo blew (and fitting 2530's) and there was no ceramic contamination of the internals what so ever.

Ive heard stories of it happening, but have only seen one person on these forums that has said and stuck by his story that it happened. Maybe we should get Myth Busters onto it? :rofl:

my car was idling really rough today and there was alot of smoke. I removed the o2 sensor where dump pipe was and noticed alot of white smoke coming out. Does this mean the turbo is dead. If this is the case, i still dont understand the rough idle. any ideas?

because most people hear a bang and take thier foot of the accelerator - first thing most people would do... so theres a chance of some bits of exaust wheel falling back into the engine?

I've been told if i ever hear a bang to keep my foot on the gas for another 5seconds to hopefully push all that shit away from inside the engine. I think it would be hard to do - keep your foot down after you hear a bang :P

myth busters.. lol .. I would have thought even if there was ceramic on the piston crowns, it wouldn't take long before it was blasted into powder anyhow.

It's probably correct though, that when you think about it, the turbo is 95% likely to blow the turbo whilst under the foot under full boost.. blowing it out the exhaust, rather than back up the intake.

RB 26 engine shave serperate exhaust manifolds for the front and rear banks of three cylinders.

Say the rear turbo goes, there is a fair amount of time when no gas is exiting the rear three cylinders. In fact, exhaust gas from the front three cylinders will help to push the ceramic pieces into the rear three chambers.

The fact that the exhaust valves are still open while the piston is on the way down also helps to suck the particles in.

myth busters.. lol .. I would have thought even if there was ceramic on the piston crowns, it wouldn't take long before it was blasted into powder anyhow.  

It's probably correct though, that when you think about it, the turbo is 95% likely to blow the turbo whilst under the foot under full boost.. blowing it out the exhaust, rather than back up the intake.

I've thought about this too, and I reckon that a turbo is most likely to blow as you lift off to shift gears. think about this, you are on full throttle, 6500rpm in 3rd, turbo is making 1.1bar boost, as you lift off, there is temporarily a restriction in front of the compressor (before the bovs react) that trys to slow down the compressor and by extension the exhaust wheel, but at this moment there is a huge amount of exhaust gas trying to still make boost.

all theory though :D

but I agree, someone should call myth busters.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...