Jump to content
SAU Community

Recommended Posts

Why would you even be driving it if you thought it had blown a turbo wheel off?

They actually do still produce boost pressure with only one turbo working, it's just very low as it is leaking boost ( a lot) but because the gap where the air excapes around the blown turbo compressor wheel is so small, it can still build some pressure.

Quite often (and I know not too many people have experience with this) a blown ceramic turbo will actually kill your entire engine.

We stripped mine down and rebuilt it about 600kms after the turbo blew (and fitting 2530's) and there was no ceramic contamination of the internals what so ever.

Ive heard stories of it happening, but have only seen one person on these forums that has said and stuck by his story that it happened. Maybe we should get Myth Busters onto it? :rofl:

my car was idling really rough today and there was alot of smoke. I removed the o2 sensor where dump pipe was and noticed alot of white smoke coming out. Does this mean the turbo is dead. If this is the case, i still dont understand the rough idle. any ideas?

because most people hear a bang and take thier foot of the accelerator - first thing most people would do... so theres a chance of some bits of exaust wheel falling back into the engine?

I've been told if i ever hear a bang to keep my foot on the gas for another 5seconds to hopefully push all that shit away from inside the engine. I think it would be hard to do - keep your foot down after you hear a bang :P

myth busters.. lol .. I would have thought even if there was ceramic on the piston crowns, it wouldn't take long before it was blasted into powder anyhow.

It's probably correct though, that when you think about it, the turbo is 95% likely to blow the turbo whilst under the foot under full boost.. blowing it out the exhaust, rather than back up the intake.

RB 26 engine shave serperate exhaust manifolds for the front and rear banks of three cylinders.

Say the rear turbo goes, there is a fair amount of time when no gas is exiting the rear three cylinders. In fact, exhaust gas from the front three cylinders will help to push the ceramic pieces into the rear three chambers.

The fact that the exhaust valves are still open while the piston is on the way down also helps to suck the particles in.

myth busters.. lol .. I would have thought even if there was ceramic on the piston crowns, it wouldn't take long before it was blasted into powder anyhow.  

It's probably correct though, that when you think about it, the turbo is 95% likely to blow the turbo whilst under the foot under full boost.. blowing it out the exhaust, rather than back up the intake.

I've thought about this too, and I reckon that a turbo is most likely to blow as you lift off to shift gears. think about this, you are on full throttle, 6500rpm in 3rd, turbo is making 1.1bar boost, as you lift off, there is temporarily a restriction in front of the compressor (before the bovs react) that trys to slow down the compressor and by extension the exhaust wheel, but at this moment there is a huge amount of exhaust gas trying to still make boost.

all theory though :D

but I agree, someone should call myth busters.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...