Jump to content
SAU Community

Recommended Posts

haha, yeh i have heard about cheap ones on ebay, but after the whole GTDNO thing i went through on here i would rather buy one from someone legit...I heard of some available from somewhere in Redcliffe for like $180, but dunno the name of the joint. Any help would be kool, if we can we might organise a group buy.

Matt

$170 each and you can have as many as you like

3" high flow

Brand: Carsound.

Have been running 18psi and lots of hard time on this one for 2.5 years now and is still good.

My car runs rich as a muther and it is still ok

I work at Midas Woolloongabba but am currently filling in for someone at our Capalaba store.

And then you can have it fitted also.

Depending on the car and setup...fitting won't be more than $80

Step One, remove cat from system.

Step two, stand cat north south over a drain.

Step three, using a hammer and screw driver, belt away at the honeycomb looking filling.

Step four, continue belting away until said honeycomb is all in the drain.

Step five, re-attach cat to system.

I did this on my secret track car, as its illegal to not run a cat on poublic roads.

Problem with a 2nd hand one is that the internals of the cat will be demolished by now

They should only be keeping good cats at most of the wreckers anyway. You can still get a secondhand good one if you look, just like buying a turbo. I did the same for an engine conversion about 6 years back and both are still going well. A cat can last for a long time as long as it is operated properly in the car it came from (correct fuel mixture, temperature.)

Step One, remove cat from system.

Step two, stand cat north south over a drain.

Step three, using a hammer and screw driver, belt away at the honeycomb looking filling.

Step four, continue belting away until said honeycomb is all in the drain.

Step five, re-attach cat to system.

I did this on my secret track car, as its illegal to not run a cat on poublic roads.

You forgot Step 6. Get pulled over by transport inspectors who tell you your cat is hollow because of the poisonous gases bellowing out the back

and Step 7. Get fined up to $5000 depending on how 'aware' you were that it was hollow.

You forgot Step 6. Get pulled over by transport inspectors who tell you your cat is hollow because of the poisonous gases bellowing out the back

and Step 7. Get fined up to $5000 depending on how 'aware' you were that it was hollow.

But what if there is no cat there? You can't be aware of a hollow cat if you don't have a cat now can you :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...