Jump to content
SAU Community

Recommended Posts

  • Replies 77
  • Created
  • Last Reply

Top Posters In This Topic

']The ceffy doesnt have a bov

it has an external venting wastegate. sure its not legal but its set up like that for track use. it sounds nothing like a bov or flutter ffs

It was hardly on boost, we (people around Mikey's car) heard it as it was leaving the complex...

hardly on boost = lies

its needs to be on or close to full boost for the gate to open or it doesnt work.

Adrian... my honest opinion is absolute shit all... not due to sau but due to the way the event was organised by cabin in some areas, ill be emailing jason fro andra this week and il pm you a copy

']hardly on boost  = lies

its needs to be on or close to  full boost for the gate to open or it doesnt work.

Adrian... my honest opinion is absolute shit all... not due to sau but due to the way the event was organised by cabin in some areas, ill be emailing jason fro andra this week and il pm you a copy

Im with you on this tj, the event wasnt organised very well, Get to the gates at dead on 12 and they hadnt open yet, had to wait for a good 15 to 20mines then there was ahold up took about another 20-30mins to get inside, *i heard that some clubs money didnt go through and they had to pay again i belived this inc sauwa*

anywayz i get to the gate tell the person who i am, and she just give me tickets and sends me off, unlike last yr were they gave u a map and told u where each car club was, this yr i had no idea where anyone was. i couldnt find antilag so i was force to park my car else where and i only found sauwa cuz i look where the RH9 GTR was.

Also there was no supercruise :) that was something which i really like about dc last yr, too bad it wasnt there this year.

I think last year it was run much better, didnt like the classes that much but hay it can only get better from here :)

I think overall the event was bigger and better, but I agree there is alot to still improve on, including club setups, speed of entry and scrutineering. I get to see things from the organisers point of view, and trust me we're working our asses off, but with better organisation things would have been much better.

Please feel free to provide me or TJ some feedback, and then we can pass it on to the organisers to make sure next year is even better.

Cheers

Paul

Yes it did Glen proving HP means very little.Steve Lee puts together a mighty engine so i cant wait to see this GTS on drag rubber.

The one thing ive seen working with trev cars is how little it takes to run fast like the white L34 Torana(Full street trim etc) at last fast friday, ran 10.9 on treaded tyres with 383rwhp but was over a very broad band.

The Hyperdrive 180SX that competed at Combat has been tickled and put-down 477.7hp at the treads this morning. Shame we didnt get time to do that before combat as I am sure it would have slipped into the 10's for sure. It was a mission and a half getting the RB25 box in there - didnt even know if that was going to work out until the night before!

The point I am getting to is that in terms of 'RESPECT' here comes another Jap Rice Rocket that can idle in traffic and throw a 10sec 1/4 down. They will start learning there's more to life than pushrods!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...