Jump to content
SAU Community

Recommended Posts

i was tightning them with 1 hand until it was firm and then pop.....

i thought the valve or whatever it was called was going down but no, the bolt broke....

anyone have a spare bolt for the cam brackets?

or will nissan charge me like $94.86 for 14 of them i dont need?

yeah, thats similar to the thing i got from bunnings the other day.. havent used it yet...

either way, i am f**ked...

i have to either drill and re-thread the hole and use a bigger bolt, or try using an easy out....

but the main question is

Does anyone have a spare cam bracket bolt i can purchase off them, or a part number for nissan... (or will they only sell me a pack of more than 1?)

yeah, but if i drill it out, wont there still be some of the old bolt left in there?

and also, i could damage some of the tread the bolt would attach it self to....

atleast if i use a easy out tool, i just have to drill a small hole into the broken bolt, then easy it out....

its about 1.5cm into the head, so might be a little tricky

If your going to replace the cam journal/cap, whatever they are called...be sure that it is toleranced for your engine. I ran into troubles when i used one of another engine on my otherwise perfect RB20.

I wouldnt think its overkill to drop off to a mechanic to be sure that the tolerances are all ok...as from the factory the gallery for the camshafts is line bored/honed (whatever the proper term:)) so sure its a bugger and agro, but best be sure:)

i snapped it replacing the cams... not from driving it...

want to do it all myself as a learning experience...

And whilst i didnt snap the stud, it diud seize in the cap which meant that i needed to source another one. I used a 2nd hand one off another RB20 that appeared to be in perfect nic, but as i said the tolerance turned out to be a bit different...so when car was off at tuners, the inlet cam became hard to turn and just about seized meaning that the cam belt skipped teeth and i ended up with bent valves:(

Im all for trying to do yourself, just be sure about the journal size should you decide to replace it

And whilst i didnt snap the stud, it diud seize in the cap which meant that i needed to source another one. I used a 2nd hand one off another RB20 that appeared to be in perfect nic, but as i said the tolerance turned out to be a bit different...so when car was off at tuners, the inlet cam became hard to turn and just about seized meaning that the cam belt skipped teeth and i ended up with bent valves:(

Im all for trying to do yourself, just be sure about the journal size should you decide to replace it

Its common for the bolts to seize in the cap , the alloy corrodes ( white stuff ) and its hard to pull the bolt out .

If you notice all the cam caps are mumbered and you must put them back whre they came from otherwise you are looking for trouble . If you must use a new one you have to torque it down then tunnel bore to suit , of course you can use a second hand one and measure the clearence but you must make sure its within specs .

Warpzor ,

the best way to get the broken bolt out is : drill as big a whole as you can without going into the thread , so about 4-5 mm will be about right . Get an easyout and you should be able to get it out . If you drill a very small hole you will snap the easyout . Make sure you drill straight .

If you stuff the thread , drill a bigger hole and put a helicoil in there .

Whatever you do dont break the easyout in there so dont force it to much and dont use a chinese aeasyout !

Good luck with it

Depending on how the bolt is snapped off, you might also be able to weld something (like a nut) onto whatever is left of the broken fastener.

If you don't really know what you are doing, it might be worthwhile getting one of the mobile thread repair type guys to come and extract the busted bolt. For $100 or so it might save a lot of time, frustration and could prevent further damage. Removing busted easy outs isn't much fun.

did the same thing on thursday last week tourqed all inlet up to 9Nm last one just spun in the head them pop thought it was the wrench clicking off but nope!! snaped in the head

stay away from ezy outs there nothing but trouble

here is what i did

a friend of mine made a jig used the cap as a guide made a dowell like object that sliped tightly into the cap taped it through the cap and slightly into the head the jig had a 3mm hole in the dead center

once clamed with the cam cap in place with the other bolt drilled really slowly using inox to cool and lube the bit, thi step is done to drill the dead center of the hole other wise there is a chance that the bit will slip and you wont get center, because the bolt is hardened steel and the head alloy, alloy is much softer and the drill bit will prefer this

once the 3mm hole is drilled get a hold of a

M6 x 1.0mm

hellicoil kit hire one if you have to itll save you alot of money,

follow the steps drill out rest of hole with the drill bit attached

then using the thread tapper cut a new thread all ensuring that you are going straight

cut all the way to the bottom of the hole

the slowly screw the helicoil into the new thread

make sure you clean out the hole before you place bolt back in

(another tip is, if you have 1 get a magnet hold it on the smaller drill bit and use the drill bit as a magnet and get all the fillings out, also use masking tape and tape over the area so no fillings get in the head)

as for bolts use any hardened or high tensile bolt got mine from repco they are M6 x 1.0 35mm witha hardness rating of 8.8 these are common bolts they are the goldy collour ones spoke to an engineer they said thay are fine because of the tension they are at

the reason i went this way is that once you have ezyouted the old bolt the thread is ****ed even if repaired has been weekened from the abuse it just coped

helicoils are stronger than the original alloy, but i just like to be safe

sorry this is such a long wined post but its something that i feel strongly bout

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
×
×
  • Create New...