Jump to content
SAU Community

Recommended Posts

  • Replies 59
  • Created
  • Last Reply

Top Posters In This Topic

i'm interested in the drivers side window glass if it's not sratched up. also want the lower part of the dash (the bit that holds the circle vent - don't need the actual vent though).

sorry about the crash. that is a pretty decent hit... :rolleyes:

GoDziLLa: i have PM you.....i need the radiators brackets off you for sure.....and regarding to your suspension....is there any chance that i can have a look first???

i will be free whole day on firday...so plz pm me your number...i will go over and take a look...thank you

  • 1 month later...

Hi Mate,

Sorry to hear about the car bud, hope no one was hurt.

I was just wandering what sort of condition the rear quarter side skirts (the small skirts behind the rear wheels) are in and if you don't mind parting with them, how much you'd like for them?

Thanks for your time mate.

Scott.

QUOTE (>GoDziLLa<)
R32 GTR damaged write-off

1990 mdl

 yellow pearl colour

Passenger side badly damaged including chassis.

Engine good condition 150,000kms

gear box O.k

diffs

All other parts are OK except left door

passenger seat and rear seat

Mods-

All 4 brand new brake disc rotors

Volk 17*9.5 wheels deep dish 3 spoke wheels

O.S Giken Twin plate clutch very good condition never slipped

KSP engineering catback exhaust and front pipe 3.5 inch

high flow cat almost new

HKS Oil cooler and Oil filter relocation kit

HKS pods

old style HKS boost controller

Essential jap tuned ECU

stereo system Kenwood stacker ,speakers pioneer deck

nismo strut brace

speed meter

might suit someone thats going to do conversion and needs most of these parts

At the moment I would like to sell whole car for $12,000

but if I get alot of offers for parts to sell seperately I will seperate them.

will post pics up soon.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...