Jump to content
SAU Community

Recommended Posts

Ok, I have a k&n pod filter on my r33 gtst. Its sucking hot air from the engine bay. It has a partion around it to reduce this, but I want to duct cold air from the front bumber. I have a standard intercooler. Has anybody else done this? Where can u get piping through to get to the pod? Would I have to cut holes through metal?

Regards,

Dan

dan_the_man,

I've got to agree with Steve, do the FMIC, it will make much more difference, then use the hole for the factory IC as the intake for the CAI. Most people tend to use the flexible silver tubing as the intake runner, but can be done with PVC, just spray it to make it look less shit.

See'ya :burnout:

a 3" holesaw will go through the metal in 10seconds. just drill a hole, then feed your pipe through. you can get hose/pipe from any hose distributor, i got mine from IHF in welshpool for $20. black - flexible. cant say it made much of a performance difference but if you want to do it, takes about 15minutes all up

Have had a partition done and that definately made a difference, mainly after sitting in traffic or on hot days the throttle response was alot crisper, alot closer to when the car is first started in the morning. A duct, at the cost of only a few dollars, couldn't hurt, and is supposed to give a better top end as well - only to the tune of a few kilowatts but better than nothing.

Just my 0.02c

Steve

I too am a bit faint hearted, just run 10lb standard, but have been known to crank it up to 12.5 (0.85bar) when its a bit cooler.

The reason being, that when in traffic, I think I am getting a bit of heat soak through the coola piping, so she tends to ping a bit on higher boost settings during the day when it warms up. Also waiting on a Z32 AFM so that I can get a better tune, then might try upping the boost a bit more.

Steve

It don't make a lot of sense to me. If the coola is big enough, it shouldn't matter what temp air is going into it, by the time it gets out of the intercooler it should be around 20-30 deg anyway.... right??:confused:

I think what I'm trying to say is that a cold air intake will only reduce the load off the coola, which isn't gonna produce a real power gain...

riggaP,

The intake temperature will dramatically effect the temperature going into the plenum, thats why everyone tries to reduce the hot air going in, either via a CAI or vented bonnet etc.

Imagine its a 30deg day, if you have no CAI and engine air goes into the cooler at 45deg, even with a big cooler you wont get the temp down much past 32deg. On the other hand if the 30deg air goes in the temp could go down to 24deg. Although it doesn't sound like alot it can make a big difference, cooler air carries more fuel which means more power, and the car is less likely to ping.

Big intercoolers are great but will not cure high intake temperatures, minimising the intake temperature is the best way.

See'ya:burnout:

totally agreed:D

or we just leave the air alone and put the cooler in the freezer every night and served chilled in da morinig:D jk

guys, as you would saw my thread, i need a new turbo.

do you think i should get a GT28 400hp? bolts on to the stock manifold.

ron

Why are you changing your turbo? What other mods do you have? Where do you expect to be getting spool up? What is the car being used for? What are your future power plans?

sorry to be asking so many questions, but I think it is important to get things in perspective otherwise any opinions would probably be no better than a yes or no answer:)

Steve

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
×
×
  • Create New...