Jump to content
SAU Community

Recommended Posts

Love these...still available?

VOLK GT-C 19x10.5 +21 all round.

Potenza GIII rubber with 9mm tread. IMMACULATE

Perfect package for an R34 GT-R or similar

Closing August 13th

$4k  (caps $100 extra)

nekomusume_gose-img600x450-1123497261img_4452.jpg

  • Replies 345
  • Created
  • Last Reply

Top Posters In This Topic

Love these...still available?

These have been relisted by the seller. Assuming the previous buyer pulled out. Volk GT-C with Potenza GIII rubber. *** listed two posts above ***

Closing October 1st.

  • 2 weeks later...

WORK VS-KF 19 inch!!! R32, R33, R34 GT-R

19x9 +21

114.3 5 hole wrapped in Pirelli P-Zero nero rubber.

2500 kms total travel.

not often seen in this condition.

Closing October 14th

estimating $2600 - $3000 delivered.

knm735-img600x450-1128669013kif_1487.jpg

knm735-img600x450-1128669025kif_1488.jpg

  • 4 weeks later...

Charles,

since you have not connected me for over a week and won't answer my PMs

can you please give me more information here about the rims I have ordered.

The auction closed 30th september and has arrived in sydney and landed in sydney on 12th nov and still haven't got them yet.

white TE37 17x9+22 $3100.

Michael

Charles,

since you have not connected me for over a week and won't answer my PMs

can you please give me more information here about the rims I have ordered.

The auction closed 30th september and has arrived in sydney and landed in sydney on 12th nov and still haven't got them yet.

white TE37 17x9+22 $3100.

Michael

Michael,

Ya got a PM regarding your new shoes. they are here and very much landed.

all good!




  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...