Jump to content
SAU Community

Recommended Posts

I searched and can't find much. Link me if it's been done before please.

I have decided to up the boost in the near future, but on a budget, so I was going to get a boost gauge, and I just bought a boost controller for $35 in this thread http://www.skylinesaustralia.com/forums/sh...155#post1427155

I want a boost gauge so I can watch it doesnt spike. I was going to go electronic but I thought I'd get a gauge for $150 so this puts this all under $200. Much better than $600 for a EBC.

However it seems I may have been mislead. There is much debate about the different gauges.

What is your opinion and why (provide links if you have read reviews) on the following gauges.

Autometer (Was under impression they had a good rep, but seems I was wrong)

Splitfire (Hear they are crap)

Sepco (A few have said they are good, most said crap)

Greddy/Trust (As expected, all good reports)

HKS (havn't found anything)

VDO (found 1 post saying they are good)

Apexi (some say they are good, some say not.

Any others?

I am trying to work out what to buy, but if I am paying $300 for a gauge, I'll pay $600 for an EBC with the gauge and bonus features.

Cheers

Chris

Link to comment
https://www.sau.com.au/forums/topic/78160-what-gauge-to-buy/
Share on other sites

Seriously, i think boost gauges going for $300 are the biggest waste of money and wank possible, unless you have a race car.. and probably then you're at the level where somebody else is monitoring the engine status using proper equipment, rather than a simple incabin gauge.

If you are getting your car tuned by an expert, they're going to be monitoring all of your knock, boost and the rest to ensure that is not dangerous using their tools. Its nice to see where your boost is at whilst driving, and what is happening re: spiking and dips, and of course the "open boost" situation is vital to keep an eye on. But a boost gauge afterall is a monitoring tool, rather than a vital engine function.

But I am a tightass, so take this with a grain of salt..

I've had $40 specco boost gauges in my last two cars, and have not had any problems over the years. They may not be the most accurate thing, but who knows whether they are not. A 1-2psi variance between actual and displayed should not a make a difference between engine failure and not (esp. with the stock turbo). They're definitely better than the stock gauge, and even many are happy enough just sticking with that as long as the car is tuned by an expert.

What Predator said.

If your car is running perfectly, then you've got no need for boost, EGT, etc gauges. You only need to watch them if you're having issues with the car, or you're a ricer.

You might get an inlet temp gauge since that's variable and outside a tuner's control, so you could manually set boost depending on the temperature. You'd have to be pretty hardcore to do so, though. Everything else should be a non-issue.

But if you're serious about driving and monitoring your car's readings, get something like the Defi gauges. You shouldn't be watching gauges when you drive, and with Defi you can set a "warning" level to let you know when something exceeds your limits, and use the "replay" function to see what everything was doing at the time of the alarm.

Well the reason I need a boost gauge are;

1) I am going to put in a mechanical boost controller. Without a guage, I might be running 30 psi (ok so slight exageration, but point is I wont know without one since the stock isnt overly accurate)

2) Once it is installed, and I have it set to the right level, it wont matter if it reads wrong as such, so long as i can see a spike. So I guess I can get a cheapy, get it set on a dyno, then just know when it spikes.

you can get the trust/gready quite cheap $118.63 at nengun and they dont need controllers or little digital boxs to run either and come in white ,black and silver and at the end of the day you know you can rely on it being accurate. :thumbsup:

this is the white one:nengun-product-288.jpg

agreed, couldn't have said it better preadator. if you must have a guage get like a $30 one, theres a trader in the for sale section doing swoosh guages for $40 ish each, oil, water, boost, fuel etc in colours that u can choose. serioulsy the best guage or "measure device" is the powefc hand controller, it shows all the values, holds max values and does graphs. handy as. if only there's a cheap easy way to get the powerfc to read boost without controlling it :)

io bought a drift one from auto barn for 50 bucks as i installed the same boost controller in my car. i ended up takin the controller out because the nut kept coming loose i dont know if its because i wasnt tightening it enough or what but i was gettin the shits with the boost changin all the time and i like my exhaust wheel right where it supposed to be not wedged in the cat or somthing

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • New CAS just turned up from NZ Wiring. Looks like a nice bit of gear.  So, yeah. Triggered, bro. Realised I may as well do the cam belt while mucking about with it so will order one of them.
    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
×
×
  • Create New...