Jump to content
SAU Community

Recommended Posts

well my car is nearly done with just a few minorsetbacks keeping me from drving it (radiator broke).

its taken me a while to amass parts and get her in the car but she is in and running.

let me know what you think.

mods:

rb20det swap

tomei procams 260/8.8 lift

greddy cam gears

greddy belt

hks exhaust mani and wastegate

hks race bov

GT30R with .63 turbine housing

rc engineering 550cc injectors

RIPS front facing plenum

fmic (24"l 6.5"h 3.5"w) bar and plate

std ecu with chip for 550's and z32 maf

greddy emanage and e-01

Link to comment
https://www.sau.com.au/forums/topic/78571-just-a-silly-s14/
Share on other sites

haha, yeah we wernt lucky enought to have the sr in our cars over here, altho with the money ive spent on the rb i could have had a right nasty ka24de.

its got its ups and downs but ive almost got her running right, once i sort out the strange boost problem (boost isnt constant, always changes) it should be fun to sneak up on ppl with.

*edit*

over here in the us its about 3.5-4k usd for a good sr front clip, where as the rb20 only cost me 1.2k usd.

while i may have spent alot of money on this setup it cost me less to build this than it would have cost to swap in a stock sr.

Link to comment
https://www.sau.com.au/forums/topic/78571-just-a-silly-s14/#findComment-1435266
Share on other sites

Haha good move than mate! Hmm maybe the 6 cylinders can be better in some ways. :)

well according to SydneyKid an engine with more cylinders and the same capacity will make more power mod for mod (I think that's what he said). So a SR20 and a RB20 mod for mod will have the RB make more power.

Link to comment
https://www.sau.com.au/forums/topic/78571-just-a-silly-s14/#findComment-1436886
Share on other sites

stock TB, rob at RIPS said that it should be good to 450bhp and if i needed more the manifold is set up for an overbore TB.

as for the filter setup, its nothing more than some wire mesh i got at the craft store (1/4" spacing i believe) and a 'detailers pad' i got at the local parts store with the foam removed.

filter gets dirty quick so it requires frequent changing, lucily its cheap to replace (bout 3$usd for a pack of 4).

Link to comment
https://www.sau.com.au/forums/topic/78571-just-a-silly-s14/#findComment-1438562
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Put a fuel pressure gauge on it. Replace the turbos. Probably completely separate issues.
    • What copper washer do you guys use on the bleeder bolts? The existing one I have I had no idea where to find it in a local store, I did buy some online but that are only 1mm thick whereas my old one is 2mm+ thick and when I put the new washer out and squeeze the top radiator hose I can hear a bit of air but not with the old one. Does this matter? The new one doesn't leak, but the inner diameter is a bit loose whereas the old one threads on the bolt.
    • Howdy all, after being out a few weeks ago on a spirited drive in my GTR I have 2 issues that oddly have appeared at the same time. Whilst accelerating quickly through the gears all of a sudden i’ve lost power at the top of third gear (below redline around 6000rpm) for no obvious reason.    From that point onwards the car has been running rich on idle, won’t really rev under load without a ton of black smoke and the odd backfire, and dying as a pull up to a set of lights unless I keep the revs up around 1500rpm. In addition when shutting down the car that same night (I was 10 minutes from home) I noticed one of the turbos was significantly noisy on wind down when shutting off the engine. After letting the car cool down overnight it starts up fine, although once it gets to temp the revs start to creep up and down, the exhaust is darker than it should be and it also sounds like it’s running rich (fat note) I’ve put a new set of plugs in it - no change, the old plugs all seemed OK with two of them being somewhat richer/fueled up than the other 3 with 1 being borderline. I’ve smoked tested the intake system via the front of the Turbos, found a split vacuum hose going to the factory boost gauge sender, which I have since replaced.  Also found another leak on the gasket coming off the rear turbo outlet, have also replaced this. After fixing both of these leaks - still have the running rich issue. I’ve also tried another pair of AFM’s - no change here After pulling off the front turbo intake pipes, there is obvious shaft play in the front turbo, which now hisses loudly on light revvs although I can’t see why this would make the car run funny even under idle. I’m curious to know why it’s running rich before I potentially replace/rebuild turbos. The car is completely stock <50,000kms  other than an exhaust. Oil and coolant are all clear. I haven’t bothered with coil packs as it looks like they won’t be the issue due to condition of the plugs. Any help appreciated as I cry myself to sleep!
    • No probs at all. I used to love trying to dig up obscure info for those in need where possible going back 20+ years on SAU.  I did have another look and couldn't come up with any closer match. I'm leaning towards those skirts in your first pic are custom fitments, cut down/extended or from another car entirely and modded to fit an R34 sedan. I would've thought someone in Japan had them and taken a photo at some stage over the last 2 decades but there's nothing. Someone out there must know surely.
×
×
  • Create New...