Jump to content
SAU Community

Recommended Posts

  • Replies 61
  • Created
  • Last Reply

Top Posters In This Topic

I'd take the Chaser, but I'm a big fan of R34 sedans too.

looks - about the same. I think they both look awesome, but in different ways. The Chaser is more of a luxury look, whereas the R34 is sportier.

performance - JZX100, but only just. 378Nm from 2400rpm versus 343(s1)/363(s2)Nm at 3200rpm is just in the Chaser's favour.

fuel economy - about the same I think.

potential - not sure what you mean here, but both engines are highly moddable if that's what you meant.

reliabilty - Toyota quality :P Nissan are good too, so I'd say about the same.

One big thing for me was resale price. Sedans often sell for a lot lower if they have a coupe equivalent. There's no coupe Chaser, so I'd say it would hold its value just a bit better. Then again, they cost more to buy in the first place, so it probably evens out.

I'm amazed nobody has compared the interiors yet :)

Here's a pic of mine. The original pics from Japan were terrible, so I thought it the series 2 JZX100s were pretty much the worst interior you could get in a car, but when I sat in it for the first time I changed my opinion very quickly.

The carbon fibre is very nice and suits the car really well, and the seats have a nice feel to them. The pattern on them isn't too special, but it's a lot nicer than I first thought.

A manual R34 Sedan weighs 1430kg and a manual JZX100 Chaser weighs 1480kg, so there's a good 50kg difference. I think the extra 35Nm and torque lower down the rev range would pretty much even it out.

Handling wise, I have no idea. I've never driven an R34 (or my own Chaser for that matter :))

EDIT: The autos are a different story. R34 = 1450kg, Chaser = 1490kg, but the auto R34 only has 333Nm. So if you're after an auto one, go the Chaser.

Chaser is hot Shane, but the R34 with the Eastbear GT-R front/kit will look damn insane and I think, in the same colour as the chaser, will turn a shitload more heads... if that's what you want!

Who can not gawk at an R34 GT-R when you see one on the streets? They have so much street presence that's for sure.

It's a little unfair to compare those two cars, as obviously they have had tens of thousands of dollars thrown at them. You'd really have to compare stock look to stock look, and I think the R34 has the edge there as look different to most cars out there.

The chaser has many cues to other cars out there. Many might not even draw an eye unless you know what you are looking at. I've seen a couple of stock looking ones out there, and often hard to distinguish it from a Camry from a distance (the ultimate insult! sorry :D)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi all, I’ve just finished fitting the timing belt on my RB25, following the standard procedure: rotate the crank twice, release the tensioner, then tighten it down. The belt feels tight, and you can see that clearly in the picture below I’ve heard some people say it’s actually better for the belt to be slightly loose rather than too tight, as excessive tension can lead to snapping. So that’s in the back of my mind. What I’m seeing is this:  • At idle, the belt looks fine.  • But when cranking and especially when revving (around 3–4,000 RPM), there’s a momentary flap/flex or flicker in the belt, which I’ve tried to capture in the video. So my question is — based on what you see, is this slight belt movement something you’d consider normal, or am I just being OCD? Could this amount of movement cause sync issues? Or is it just a harmless bit of flex under load?   from what I know belt flap and flex is expected when crank spins up and pull cam with it Would appreciate any thoughts or similar experiences.     IMG_7656.mov IMG_7657.mov
    • I've replaced the front brakes of my NA to 324 brembos and 350z calipers: i'm going for 225/40-18 up front and 245/35-18 in the back. I have Rays 7.5*19 ET35(225/35) in the front with 5mm spacers otherwise the calipers "lock up/ won't rotate". When i use the calculator i come up with 8*18 ET30 for 225/40...... but not sure i get problems with the calipers. Anyone riding around with 18 inch. that can confirm "that it'll fit"? In the back it's 7.5*9 ET30 (245/30) with the 5mm spacers, but there is no problem with the standard small brakes, so i want to take 8.5*18 ET25 (245/35).
    • Lol.. but then.. always come back to a JDM..
    • Glad to hear. If possible, get your tuner to check air's to make sure everything is still where it should be.
    • The problem with FB/Insta/Reddit etc comments relating to cars is simple. You get to ask a question once, and get one round of replies. For things that can actually be answered in a few lines of text, once, it's fine. After 6 hours, your original question is lost to the void. There are no follow ups, additional questions, anything. No project car is ever such a simple list of questions to ask. You need discussion.
×
×
  • Create New...