Jump to content
SAU Community

Recommended Posts

Hi Ian, happens all the time, Duncan correctly mentioned driver issues. But the track really gets crappy as the day wears on, more people bring stuff back on after a few offs, the ambient air temp goes up, so less power, the engine, tyres, brakes etc go off as well. The race team RX7 was within 5/100ths of the outright IP lap record in the Sunday Morning race and couldn't get within 1 sec of it in the afternoon race.

Hi Gary, thanks for that explanaition. One guy told me also that in the afternoon the cars suffer from "heat soak" and just don't perform as well. Lower top speeds on the straight etc. And if you can't get a time in the morning your wasting your time in the afternoon.

Ian

  • Replies 108
  • Created
  • Last Reply

Top Posters In This Topic

Hi Gary, thanks for that explanaition. One guy told me also that in the afternoon the cars suffer from "heat soak" and just don't perform as well. Lower top speeds on the straight etc. And if you can't get a time in the morning your wasting your time in the afternoon.

Ian

Yep, it's all downhill after midday, even worse if I eat too much lunch. I have never been very good at turning up and racking up a time first run in the morning though. I need a few laps to get the brain up to speed. So I tend to get faster as the day goes on, even at Oran Park where I have done a thousand laps or so.

:P cheers :D

Yep, it's all downhill after midday, even worse if I eat too much lunch.  I have never been very good at turning up and racking up a time first run in the morning though.  I need a few laps to get the brain up to speed.  So I tend to get faster as the day goes on, even at Oran Park where I have done a thousand laps or so.

:P cheers  :D

Gary, that's what surprised me because on my second lap of the 1st Supersprint, I was still relearning the track and not pushing the car and being a bit cautious sort of feeling my way a bit. I was surprised at my time 1:49:57 on my second lap and thought to myself, I'm going to get a 1:48 something. Never happended, although I drove smoothly and I thought a little more agressively on later laps. Didn't spin or lock the brakes up once all day. I enjoyed it all though. Can't wait to get back on Oran Park on the 28th August.

Ian

Ian,

I have joined up with the SSCC and have my entry in for tomorrows sprint at EC. Just finished doing all the brakes etc and it's all systems go for tomorrow. Should be a good day.

If anyone is coming out I will be in the grey 32 GTR with Rice Engineering stickers down the sides, car 295.

should be a top day :)

Fly that flag Duncan well done and I am impressed. I might loook at you different from now on. I have been busy and have not been on the forum much sorry for the late well done. Beer Baron was at the SAU drag day and told me you were running that arfternoon. It was very tempting to come out but playing Grand Turismo 6 days a week and only Sunday family day well it is hard. I would rather be driving as you would understand like tomorrow at E Creek in the slot car for a Supersprint.

john you should come out. I am racing in the GTR. Bring your Zed Sled. They will still be taking entries right up until the 8:45am drivers briefing.

should be a good day :)

Gary you are being very kind, you guys had the numbers on me all weekend, the closest I got was .3 seconds, I can't wait for the next round once we put a tune on the car.

I had a really good weekend of racing, Qualified 4th and finished 2nd, 2nd and 5th.

The last race in particular was great, I got a top start, managed to chop chop the BSM GTR off the line and into turn 1 (unlike the race before where I stupidly left the door open). Held the lead for the first 2 laps but in the end Coles was too quick and there was no point trying to block him for 10 laps so thru he went with a quick dent on the way thru. At least I got to return the favour on the exit of the corner (Gary is HGE32R imprinted in the rear bar lol)

A lap later that pesky WRX got thru as well with another dent in the front quarter panel (have these guys been playing too much GT4?) leaving me a comfortable 3rd. From there the other GTR and the WRX were having a great battle which let me catch up to them nicely. Until....

I arrived at turn 10 with *no* front brakes...I hit them at the usual braking mark just before the 100m sign and got....nothing....I kind of pitched it into the corner since the only other option was deep into the kitty litter, and since the rear brakes were still working OK I did a lovely 720o spin, and recovered to 5th. Another spin a couple of laps later with the same problem and I came home 5th.

So, overall it was a great weekend, I was stoked to be competitive especially considering the development that has gone into the other cars. I think once we can keep the engine together more than 2 race meets in a row that we might have a chance outright :O

A huge thanks to Neil and Kel for their support thru the weekend, and to the rest of the team for all their help getting me on track in the first place. It was really great to get out there at last!

Well done mate. I was keen to whip across to Wakefield to catch up while I was in Canberra all weekend doing finals on the rental house but was just too damn busy. Didn't even have time to catch up with any of the ACT crew. Still recovering from back mechanics 3 weeks ago so everything takes 3-4 times longer to get done.

So will we get some TV coverage of this one??

  I think once we can keep the engine together more than 2 race meets in a row that we might have a chance outright :

That's a worry, did I hear bottom end knocks?

Please tell GTRgeoff what the final prognosis is, he likes to hear about RB26 bottoms.

What sort of sump arrangement are you running?

Oil return to sump?

PM me if you like.

:( cheers :(

PS; Regardless of the modest approach you take, the BSM budget is MUCH larger, so on a dollar per lap time basis you are miles in front.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...