Jump to content
SAU Community

Recommended Posts

I would say "just fit" lol Im sure you would encounter some scrubbing. When i had my 10.5 wide on the back over 1##km/ph the rear would be pressed down on the tyre causing it to wear pretty bad.

Looks awesome though!

Where did you get the rear guards worked on?

at top one for the back.and as for the front when i get them done ill let you know who i used.

I wouldnt say perfect considering the wheels stick out an inch and the guards have to be lipped and rolled.

Here a few quick pics i took of my 10' wide 18s on the rear:

Here is the view straight up and down

Photo0112.jpg

And off to the side a bit.

Photo0113.jpg

Just finished fitment of my Volk GTCS

Tyres - 235/35/19 up front, 265/35(its 5cm thick 35 profile my ass!)/19

Rims:

Front - 19x8.5 JJ Offset +27

Rear - 19x9.5 JJ Offset +34

Right on the guards

Fitted Advan V103 Sport - wow they are great tyres, silicone is yet to wear away and they stick like well you know. Rears are Pilot sport, They are so loud I can hear them over the exhaust. Took them awhile to heat up too and until they did I had shit all grip on boost. BTW the pilot sport 265 was as wide as the 235 Yokohama!

No scrubbing car sits at recommended 301cm wheel to arch hight (cant remember exact recommendation for my car)

Edited by DECIM8
Just finished fitment of my Volk GTCS

Tyres - 235/35/19 up front, 265/35(its 5cm thick 35 profile my ass!)/19

Rims:

Front - 19x8.5 JJ Offset +27

Rear - 19x9.5 JJ Offset +34

Right on the guards

Fitted Advan V103 Sport - wow they are great tyres, silicone is yet to wear away and they stick like well you know. Rears are Pilot sport, They are so loud I can hear them over the exhaust. Took them awhile to heat up too and until they did I had shit all grip on boost. BTW the pilot sport 265 was as wide as the 235 Yokohama!

No scrubbing car sits at recommended 301cm wheel to arch hight (cant remember exact recommendation for my car)

มีของดีอย่างนี้ต้องโชว์ครับ

ขอดูรูปหน่อยดิ

Alright, Not the best photo was in that sort of night sort of day period where no camera will surfice. Anyway its attached when I get some lower profile tyres I will put it on the floor.

Hope you like :)

post-34434-1231321676_thumb.jpg

The question of what wheel size fits what Skyline comes up so often I though this might be a good place to post your own wheel dimensions.

Just copy and fill in the table;

Skyline model = GTR R34 V spec 2000 model

Wheel diameter = 18"

Wheel width = 10"

Wheel offset = +12

Tyre size = 285 - 35 - 18

Modifications to fit = nil fits perfect. Cant go wider width the wheel will not have a full turning circle.

Just finished fitment of my Volk GTCS

Tyres - 235/35/19 up front, 265/35(its 5cm thick 35 profile my ass!)/19

Rims:

Front - 19x8.5 JJ Offset +27

Rear - 19x9.5 JJ Offset +34

Right on the guards

Fitted Advan V103 Sport - wow they are great tyres, silicone is yet to wear away and they stick like well you know. Rears are Pilot sport, They are so loud I can hear them over the exhaust. Took them awhile to heat up too and until they did I had shit all grip on boost. BTW the pilot sport 265 was as wide as the 235 Yokohama!

No scrubbing car sits at recommended 301cm wheel to arch hight (cant remember exact recommendation for my car)

im suprised theres no scrubbing even with 265 on the rears but then the high offset would help it not scrub i guess.

these 19's were the wrong offset...rubbin on my brake calipers on the front..got the right offset...just clears the calipers enough to spin the rims

it's a sign from the big man telling u to get rid of them :(

but seriously, offset doesnt define brake clearance, the disk height does that.

  • 2 weeks later...
i pose a bit of a question to you all...

Would R32 GTR rims (16 x 8, +30 offset) fit on an R32 GTS-t, without hitting on anything (assuming stock calipers/rotors) and without rubbing on the guards?

I am running r32 gtr wheels and 225's on my r32 gtst and haven't had any problems with rubbing at all but my car is still at standerd height

  • 4 weeks later...
I wouldnt say perfect considering the wheels stick out an inch and the guards have to be lipped and rolled.

I would say near perfect! In my opinion if you don't have to at least roll the guards you have chosen the wrong wheels. The opinion above is why the Australian modified car scene fails as a whole, most people don't have a clue about good wheel fitment, though that is slowly changing!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Power is fed to the ECU when the ignition switch is switched to IGN, at terminal 58. That same wire also connects to the ECCS relay to provide both the coil power and the contact side. When the ECU sees power at 58 it switches 16 to earth, which pulls the ECCS relay on, which feeds main power into the ECU and also to a bunch of other things. None of this is directly involved in the fuel pump - it just has to happen first. The ECU will pull terminal 18 to earth when it wants the fuel pump to run. This allows the fuel pump relay to pull in, which switches power on into the rest of the fuel pump control equipment. The fuel pump control regulator is controlled from terminal 104 on the ECU and is switched high or low depending on whether the ECU thinks the pump needs to run high or low. (I don't know which way around that is, and it really doesn't matter right now). The fuel pump control reg is really just a resistor that controls how the power through the pump goes to earth. Either straight to earth, or via the resistor. This part doesn't matter much to us today. The power to the fuel pump relay comes from one of the switched wires from the IGN switch and fusebox that is not shown off to the left of this page. That power runs the fuel pump relay coil and a number of other engine peripherals. Those peripherals don't really matter. All that matters is that there should be power available at the relay when the key is in the right position. At least - I think it's switched. If it's not switched, then power will be there all the time. Either way, if you don't have power there when you need it (ie, key on) then it won't work. The input-output switching side of the relay gains its power from a line similar (but not the same as) the one that feeds the ECU. SO I presume that is switched. Again, if there is not power there when you need it, then you have to look upstream. And... the upshot of all that? There is no "ground" at the fuel pump relay. Where you say: and say that pin 1 Black/Pink is ground, that is not true. The ECU trigger is AF73, is black/pink, and is the "ground". When the ECU says it is. The Blue/White wire is the "constant" 12V to power the relay's coil. And when I say "constant", I mean it may well only be on when the key is on. As I said above. So, when the ECU says not to be running the pump (which is any time after about 3s of switching on, with no crank signal or engine speed yet), then you should see 12V at both 1 and 2. Because the 12V will be all the way up to the ECU terminal 18, waiting to be switched to ground. When the ECU switches the fuel pump on, then AF73 should go to ~0V, having been switched to ground and the voltage drop now occurring over the relay coil. 3 & 5 are easy. 5 is the other "constant" 12V, that may or may not be constant but will very much want to be there when the key is on. Same as above. 3 goes to the pump. There should never be 12V visible at 3 unless the relay is pulled in. As to where the immobiliser might have been spliced into all this.... It will either have to be on wire AF70 or AF71, whichever is most accessible near the alarm. Given that all those wires run from the engine bay fusebox or the ECU, via the driver's area to the rear of the car, it could really be either. AF70 will be the same colour from the appropriate fuse all the way to the pump. If it has been cut and is dangling, you should be able to see that  in that area somewhere. Same with AF71.   You really should be able to force the pump to run. Just jump 12V onto AF72 and it should go. That will prove that the pump itself is willing to go along with you when you sort out the upstream. You really should be able to force the fuel pump relay on. Just short AF73 to earth when the key is on. If the pump runs, then the relay is fine, and all the power up to both inputs on the relay is fine. If it doesn't run (and given that you checked the relay itself actually works) then one or both of AF70 and AF71 are not bringing power to the game.
    • @PranK can you elaborate further on the Colorlock Dye? The website has a lot of options. I'm sure you've done all the research. I have old genuine leather seats that I have bought various refurbing creams and such, but never a dye. Any info on how long it lasts? Does it wash out? Is it a hassle? What product do I actually need? Am I just buying this kit and following the steps the page advises or something else? https://www.colourlockaustralia.com.au/colourlock-leather-repair-kit-dye.html
    • These going to fit over the big brakes? I'd be reeeeeeeeaaaall hesitant to believe so.
    • The leather work properly stunned me. Again, I am thankful that the leather was in such good condition. I'm not sure what the indent is at the top of the passenger seat. Like somebody was sitting in it with a golf ball between their shoulders. The wheels are more grey than silver now and missing a lot of gloss.  Here's one with nice silver wheels.
    • It's amazing how well the works on the leather seats. Looks mint. Looking forward to see how you go with the wheels. They do suit the car! Gutter rash is easy to fix, but I'm curious about getting the colour done.
×
×
  • Create New...