Jump to content
SAU Community

Recommended Posts

here is a 9.5 rim with 275/35/18 (on the rear only of course being a GTST).

2 things to keep in mind though.

Just because a tyre is 275 (or whatever width for that matter) doesn't mean it is exactly. Iv seen 2 255 tyres next to each other and 1 was over 1cm wider than the other. Same goes for sidewall profile. ALso for rim width too from what iv been told.

And, really how it looks also depends a bit on how the car sits- e.g. offset in the guards, camber, height.

post-68049-0-62625500-1404805257_thumb.jpg

post-68049-0-02044200-1404805269_thumb.jpeg

Hey guys is there anyone out there running 9inch wide rims with +35 offset on a r33 gtst i have been researching to see how they could fit with but havent had much luck

Start from page 1 on this thread. Just about every wheel/tire configuration has been done.... especially on a R33 GTST.

  • Like 1

Hello. I'm setting up a r33 4 door

I'm gona be using 18x9.5 with 225 40 all round

I'm not sure what offset to use.

My settings will be 0 camber rear and -3 front

(Also) my front lower controll arm is pushed out 20mm for my drift steerin lock needs.

I'm looking for flush or 10mm poke all round

One other thing to think about is I would like the same off set all round so I can rotate at track days when my tyres are getting low.

Any ideas? +22?

How low are you going? Pulling fenders? 4 doors have a different rear quarter panel than two doors so I'm not sure how that'll turn out nor really can help you. Front, suggest a 30-35 or more. If you already added 20 in front because of arm, it'll add more camber and length right off the bat and will affect normal setups cuz it messes with hub location. I have Driftworks lower and uppers. I'm running a 18x9.5 +30 245/40 w/ -1. It sticks out a few but not much. This might be a trial and error adventure for you. Find some buddies with different wheels to find the offset for you. Bribe them with beer if needed.

here is a 9.5 rim with 275/35/18 (on the rear only of course being a GTST).

2 things to keep in mind though.

Just because a tyre is 275 (or whatever width for that matter) doesn't mean it is exactly. Iv seen 2 255 tyres next to each other and 1 was over 1cm wider than the other. Same goes for sidewall profile. ALso for rim width too from what iv been told.

And, really how it looks also depends a bit on how the car sits- e.g. offset in the guards, camber, height.

attachicon.giftrack.jpg

attachicon.gif191972_10150429449045244_4328563_o.jpeg

Curious to know what offset you are running? My 9+22 sits out slightly further than this. Sorry if it has been mentioned. Is it a 9.5 on the front as well? Btw nice clean car.

The rears are 9.5+38 with a 275/35/18 tyre. So yours would be 9.5mm further out (16mm more offset -6.5mm less rim width on the outer edge). Also keep in mind my ride height (fairly low) combined with camber arms running less than .5 degree of camber- so sitting very straight.

Fronts are 8.5 with a 235/35/18 tyre. They actually sit in a bit further than is aesthetically perfect but they do not rub anywhere under any conditions. Though it does in contrast also make the back and the dish look fatter :P

Here are some pics from the front so you can get more of an idea what it looks like.

Yes she WAS a clean car. I am assuming it isn't anymore as it was stolen last year and never recovered. I was praying for the scum to be found wrapped around a pole...

post-68049-0-89336300-1405925724_thumb.jpg

post-68049-0-74259400-1405925730_thumb.jpg

Edited by jjman

Here is my R33 Skyline GTS-t with 18" Enkei RPF1

Front 18X9.5 + 15. 235 tyre with -3 degrees of camber

Rear 18x10 + 38 (5mm spacer) 265 tyre with -2 degrees of camber.

I could just squeeze my fingernail under the rear guard

post-59293-0-60523500-1386652569.jpg

Here is a white 33 which out did mine

Enkei RPF1′s – 10.5″ +15 offset wrapped in 255/35r18 (rear) 9.5″ +35 offset wrapped in 225/40r18 (front)

Shazs-R33-Front-Quarter.jpg

Shazs-R33-Rear-Quarter.jpg

Shaz-R33-Feature-Set-Upload5.jpg

Shaz-R33-Feature-Set-Upload-6.jpg

shaz-resize-1.jpg

Fronts look like much lower offset than +35. I'd say more like +15, else running spacers. I run 18x9 +30 which would be roughly same as 9.5+35 and mine sit in much further.

Looks tops though, really like RPF01s in good size and offset on R33s. Also agree on your opinion of XD9s (what I have) ;)

Does anyone know if

Front: 18 x 9.5 +35

Rear: 18 x 9.5 +20

Will fit on r32 gtst (gts4) with rolling no flailing, not super low, std camber.

It's a 32 gts4 so I need to run same size and width. Cheers

Most likely yes. Here is a 18 x 9.5 +12 rim on the front of my GTS-t. It is "lowered" on pedders springs and bilstein shocks(still super high) and has no guard rolling. There are no issues with it hitting anything because it is so damn high lol.

fitment.jpg

Hi all, I'm purchasing a set of rota grids in the next month. I originally wanted 18x8.5 +35 front & 18x9.5 +30 rear. Now the offsets they stock are the other way around. Will this make any difference on how they will look or mods needed. Will they still sit flush?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...