Jump to content
SAU Community

Recommended Posts

won't be able to put the car on the dyno as it will be off the road as of the 7th of october ready to put the new motor in but i will bring my beasty 1975 ke30 corolla down and watch and meet you guys and put some names to faces!

  • Replies 294
  • Created
  • Last Reply

Top Posters In This Topic

Nothing wrong with the VL's. :)

The VL' should be on par to that of the rb25det running the same mods, if not a little better due to the 25's crap ecu that does its rich and retard.

Come along Nath, pass through and we will head down together.

Edited by Cubes

I've seen REALLY low cars get up there no probs

Shaun backs them onto the footpath first, then up the driveway. It seems to work well

Short of getting a set of ramps to put on the driveway, what else could you do?

Ok, ill put mine in....im sure it'll be going by then.

Itll only be around 220rwkw...hell bring on the shootout mode, ill be up around 239rwkw :P

Shauns driveway is no probs. If you cant get your car up it (or Shaun) then its too damn low to start with ricers....

tried to get jaffa along, but he'll be at work :D

If a couple of people come on the day without registering interest here, is that a problem? If so, i'll find out from them for sure and post names.

Edited by GFXman

hey gtrGhosTDoGG11,

When can i get my steering wheel back? saw it yesterday closeup and its absolute sh!thouse, even your seats got a tear but a deals a deal. I had to also get a new fuel reg for $180. My car will be ready for sure unless i damage something dyno tuning next wk but hopefully ill be cracking 300rwkw :D Oh btw i also will need to put in some iridiums b4 dyno, same job isnt it?

Edited by popeye132

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...