Jump to content
SAU Community

Recommended Posts

d2 Coilovers for R33 cost me 1.5k Installed

Give EVOR a call they have D2 and Tein coilovers ;)

hey man where is EVOR? excuse my ignorance but i have never heard of them before.

do u have a no. i can ring them on?

how does your car look........... nice and slammed? how do u rate the d2 coilies?

Link to comment
https://www.sau.com.au/forums/topic/87787-coil-overs/#findComment-1586528
Share on other sites

Hicas lock kit can be bought from $150. Try Xspeed, they did my GTR for about $250 installed.

How much do you wanna spend on a set of coilies coz i'm leaving for Japan again next month.

Cheers

hey man

my budget is about 1.5k but if i can get some good ones cheaper ill go for them...... after all i not the only one up for a bargain ;)

anyway how could we come to an arrangment, monies etc whilst you r in japan?

Link to comment
https://www.sau.com.au/forums/topic/87787-coil-overs/#findComment-1586546
Share on other sites

hey man where is EVOR? excuse my ignorance but i have never heard of them before.

do u have a no. i can ring them on?

how does your car look........... nice and slammed? how do u rate the d2 coilies?

sorry about the late reply;

Evolution R

Unit 3, 9 Capel Court, Bentley

9358 0288

0421 387 888

The coilover are awsome :) they come with a 1 year warrenty have any problem just take them straight back to EVOR and they will get you a new set.

My car was weird at the moment as when i put the coilovers in a lowed the rear and had the front rasied abit as i had a huge frontbar which would fit everything now that i have stock frontbar in my car looks like a lift kit, when i get the time i will lower the front myself

Link to comment
https://www.sau.com.au/forums/topic/87787-coil-overs/#findComment-1588389
Share on other sites

I keep the HD Systems coilovers in stock for the R33 - you're looking at about 1400 installed for the HS type seen here:

http://www.otomoto.com.au/HDSystems/index.htm

Also have some higher end ST Design coillies at about 1800 installed.

Jash

Link to comment
https://www.sau.com.au/forums/topic/87787-coil-overs/#findComment-1589638
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thank you, 100% the intent. New coils were due and the 17" sixers look/feel loads better than the stock wheels. The aero options are so spot on.   Thanks for the warm welcome, all!
    • 98 r34 gtt Been rocking my latest setup and car running like never before. Have put a good 200 miles on it since all the latest changes and additions. everything is dialed in and have been driving it a bunch.   However, all a sudden last weekend as soon as I pushed throttle passed 4k and the engine stumbles, (slow or fast acceleration) hesitates and doesn’t go above 4100 or so, like a misfire. Everything else seems fine. I had a “good” set of coil packs that I removed from car when I first got it when I changed them over to new coils. I swapped out current ones for those, but no change. I also changed the plugs, no change. Seems to rev over 4 when out of gear with no load just fine no “misfire”, but as soon as its in gear with a load of any kind, it “misfires” as soon as rpm drop back below 4 k it runs perfectly, smooth, starts, restarts and drives fine as long as I keep it below 4 k while in gear. All readings look fine, no CEL   Any idea as to what could all a sudden cause an issue when pushing rpms passed 4 k?
    • When you say your cams are 272/262 is that 272in and 262ex?
    • We're arguing semantics. I am saying 45 accel and a 55 deccel ramp are "2 ways". Even a 45 degree ramp and an 89 degree ramp is "2 ways", because it is literally... two ways. The cusco 55/30 ramp is a 2 way. It's two ways. I get it though - in normal nomenclature a "2 way" would be 45/45 or 55/55 or 60/60 i.e the same locking in both directions. And something like 45/65 would be considered "1.5 way". I would then say if we're getting into the nitty gritty then every locking diff is a "2 way" diff and we should not speak in 1.5, or 2 ways but ramp angles instead. Which ofc if one of those ramp angles is 90deg, that side is not doing any locking. :p So Nismo don't obviously sell 3 things. The fact of the matter that they only sell two items really goes to show that there's a 2 way and a "1,5 way" which is really a 1 way. I believe the actual lockup for the 'adjustability' of the GT pro is really just setting preload for when the ramps actually start locking up. It's not changing how much 'wayness' there is. It is (somehow) horribly explained. People just buy whatever diff and go "locks up good bruh" and that's what ends up on socials forever.  
×
×
  • Create New...