Jump to content
SAU Community

Recommended Posts

I have just had my car on the dyno today, and was told it was hitting a boost cut at 12psi. I thought the cut would have been higher than that. Can anybody comfirm what the boost cut is so I can investigate further if it isn't.

I ended up getting 208 rwkw at 5615rpm on 10psi with a 2 3/4 cat back exhaust, k&N panel filter and a SAFC II, so I am happy, but 12psi would make me even happier

Cheers

Glenn

Link to comment
https://www.sau.com.au/forums/topic/88600-r34-gtt-boost-cut/
Share on other sites

tats a pretty nice figure with just exhaust, filter, safc and 10 psi

satanic on this forum had 194 or something with the same mods except he had FMIC and just a catback so i guess its pretty similar

i think some ppl experience boost cut at anything above 10 with the standard ecu

i thought the safc would remove the boost cut? hmm, i guess im wrong then

Sounds like a pretty happy dyno but just the same it sounds alright to me. Knowing what I know now (as opposed to before I went too far) I would sit back and accept that as pretty good and enjoy it.

Post your dyno sheet if you like and we can comment on that.

I mean Richen the fuel, retard the timing, recover.

repeat.

I didn't want you to think I thought you were a rich retard!!!

Rich/Retard is what happens when the stock computer sees higher than expected airflow/boost etc.

Hey guys what does the standard boost gauge go up to??

does +1 mean 14 or so psi??

is it fairly accurate?

mine goes up to about 2mm from the +1?

roughly how much would it boosting do you guys reckon??

my gtt when fully boosting sometimes pops a little at around 5krpm could this be the boost cut??

i really would like to try and find out what is causing this before i go and replace coils and get safc etc??

That's not boost/fuel cut. Boost fuel/cut will make the car jerk and will throw you a bit forward if you are accelerating hard enough when it does it.

Yes 1 on the stock boost gauge is approximately 14psi.

The popping is unburnt fuel in the exhaust and nothing to worry about.

Your graph looks very similar to mine when it was tuned poorly running 13-14 psi of boost. You may want to get that checked out.

Another R34GTT tune... 208rwkw is a very good number! I presume your car is a manual? This may explain the variance of 13-14kw between yours and mine since we have pretty much the same mods.

However, if you look at the graph in my blog, you'll notice that curve does not have any 'kinks' in it... maybe if you sort that out you'll be looking at 220rwkw which should be the correct difference between auto and manual.

Hey guys what does the standard boost gauge go up to??

does +1 mean 14 or so psi??

is it fairly accurate?

mine goes up to about 2mm from the +1?

roughly how much would it boosting do you guys reckon??

my gtt when fully boosting sometimes pops a little at around 5krpm could this be the boost cut??

i really would like to try and find out what is causing this before i go and replace coils and get safc etc??

Sorry to sort of diverge from the topic but is yours a series 2 R34 because of the R34 GTT's I've seen around here (QLD), the series 2 cars seem to boost close to the +1 but the series 1s go to about the 3/4 line (the mark before) and rarely over that.

Sorry to sort of diverge from the topic but is yours a series 2 R34 because of the R34 GTT's I've seen around here (QLD), the series 2 cars seem to boost close to the +1 but the series 1s go to about the 3/4 line (the mark before) and rarely over that.

mine is a series one

with exhaust fmic airfilter.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
    • I have more than enough digging, laying blocks, moving gravel, airrating, feeding and top soiling the grass, and setting up the veggie gardens growing some seedlings,  and then removing all the unused rock to keep me busy for the next few months at least,  hopefully the rain stops soon so I can get a few hours in this arvo, but, before that Sunday is washing day, is every body happy, you bet your life we are Nice country road day drives are a day off whenever I'm muscle sore from all the landscaping at the moment, but, more epic multiple day drives will start once the majority of the big jobs outside are completed
×
×
  • Create New...