Jump to content
SAU Community

Recommended Posts

haha, yeah, ive got a good vid of the launch i managed yesterday coming soon

its not the track thats going to be the main issue, it will be the driver haha

Where is this video you speak so fondly of?

post-74398-0-51538100-1296886525_thumb.jpg

post-74398-0-58194600-1296886545_thumb.jpg

Has any one got a good rb26 head for sale as im in the build again with my car the last head went really soft and kept lifting the head and blowing head gaskets it probly didnt like the 43 pound boost i ran through it at GT Garages first dyno comp Also is any one interested in some really good piston sets we are getting custom made at cosworth in the UK the will be the same design as an F1 car very strong we need to order 10 sets to get this to happen they will suit rb engine 86.5 mm at 10.5 to 1 compression ratio I think we have finally worked out with the 26/30 build what works and what doesnt work to make them very reliable and strong

Edited by andogtr

Hopefully about 3 months Rob bit like you had a bit of bad luck with a few engine problems but hopefully got a combo now that will not fail changing alot of the set up this time It all takes time money and motivation and learning the hard way hope you get yours sorted this time

post-74398-0-51538100-1296886525_thumb.jpg

post-74398-0-58194600-1296886545_thumb.jpg

Has any one got a good rb26 head for sale as im in the build again with my car the last head went really soft and kept lifting the head and blowing head gaskets it probly didnt like the 43 pound boost i ran through it at GT Garages first dyno comp Also is any one interested in some really good piston sets we are getting custom made at cosworth in the UK the will be the same design as an F1 car very strong we need to order 10 sets to get this to happen they will suit rb engine 86.5 mm at 10.5 to 1 compression ratio I think we have finally worked out with the 26/30 build what works and what doesnt work to make them very reliable and strong

aaargh ando, i wish you could find these , . buttons! its an effort reading that on a sunday! haha

HIGH comp, what fuel do you plan on using in your car with those bad boys?

Are you just after a standard head so you can do the work on it?

I have some Blitz 1000cc injectors and twin entry rail to suit RB26 if anyone is interested.

Also where in Tassie can I have my turbo checked out. Just want to make sure its good to go on the new engine

there is a turbo place in Don, Devonport,

dunno what its like, but there is one there!

I went there once...

Asked for a waste gate spring. Then the dude got really confused. His head almost exploded when I said it was for an external wastegate.

I just sighed and walked away. Me thinks they only do like trucks and the likes.

guages in just need to get a sterio 2 fill in the big hole from old guages and get some new buttons :)

I've got a double Din touch screen headunit if you want it?

5430166104_6c3ab9d9d5_z.jpg

Just pulled it out of my Skyline when they were putting the cage in.

Edited by zoidbergmerc

I've got no idea what it is, there's nothing on it to tell me wtf it is.

All I know it's like a GPS and phone and DVD player and it's impossible to tune the radio on it and randomly attacks you when you change gears. I hate it.

Shoot me a PM if you want it. I'll swap you your brakes for it :P

I have some Blitz 1000cc injectors and twin entry rail to suit RB26 if anyone is interested.

Also where in Tassie can I have my turbo checked out. Just want to make sure its good to go on the new engine

you could just buy my turbo setup rob. .:ph34r:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
    • So M12 and sealant should be fine?    NPT ” because that’s what I had and what I could get atm. 
    • Wouldn’t touch par if they gave it to me. You need to ask how much power you’re looking to make and then add about 50% to it because that’s what you’ll end up making  The factory box says no more at about 350kw or so, the upgraded synchro boxes won’t handle much over 500kw for long and at that point you’re looking at an auto or dog engagement manual,  once you’ve gone dog engagement you may as well go sequential, they cost a little bit more but it’s worth it  also while you’re at it you should upgrade the transfer case with 10 friction plates 
×
×
  • Create New...