Jump to content
SAU Community

Recommended Posts

So much happening! :D Very exciting stuff, I've done a little to mine but I'll post that over in my thread because there is a fair few pics!

Bushy: Really excited to see you're making some awesome progress; Can't wait to see you on the track again!

Brain: Loving the flares, they don't look too bad even in black. Are you going to colour code them?

Young: That is one Sexy 31, love it! Wheels are mad and boss fitment!

That 31 is porn,

Yeah it is a little bit lower then before I think it may be the angle im taking the pics on as well, I have around 100-110mm clearance on the front bar.

I'll take some better pics when i get it out of the garge.

I think I may just keep them black for now, I'm not 100% sure yet

Slight correction to my last post...I meant to say cam seals were replaced, not crankshaft seals hah. Doesn't look like I can edit the post.

Yep, after 20 Mins you're committed!

  • 2 weeks later...

That thing better get low ^^ . Ok im bored so i shall waffle , blue snotter is very close to rego , just need to pull my finger out and finish off a few small things . After a fail weekend last weekend where i missed out on the charity ride day over mis communication with people , i finally have my other hq ready for the track again and 28 is back in full swing after the issues in Melbourne . How did everyone go last weekend at the track day? Im Devo i didn't make it :(

Doing some wheel bearing moves on the 31

Also need to redo the passenger side front brake hard line flare, anyone know where you get the hard line brake nuts from? and if a supercheap style flare tool can do the correct flare?

few new pics of mine (still in the garage) after getting another pair of flares, should have them on & out of the garage by next week.

post-71390-0-09140300-1344320633_thumb.jpgpost-71390-0-80884600-1344320676_thumb.jpg

this is starting to grow on me. Look forward to seeing it finished for next Sunday....

Yeah im good mate thanks , basically , i ran out of talent . I was playing with tyre pressures and a couple other things with the car and came through the esses too hard , got sideways , the clutch wouldn't dis engage properly and bam! . Only damaged the nose cone and front guard luckily (and bonnet and door) . My bad :s

I'm struggling highly for motivation at the moment.

Also for the first time in about 3 outings I actually jacked my car up to check it and found some epic inner wheel damage from the last prac day. My spotter kept edging me deeper and deeper to turn 1 untill I broke it. Also gave the chassis a good knock from another ripple strip adventure. Otherwise it's all sweet and ready to go for round 3.

I have several aspects to revamp on the. Car but can't seem to get into it. Any one got a way to get yourself motivated?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...