Jump to content
SAU Community

Recommended Posts

Hey ppls

Well, some of you lucky people may have recieved parts from me, mainly radiator guides.

Anywhoo. I need a Japlish motto for my parts to engrave, or just provide stickers for fun.

ARC's motto is as follows

The ARC product is wonders asseembiled project. The present comfortable and unknown car life with ARC power.

The name of my parts will be called:

Bass Junky's Bits

Bass Junky give total satisfaction power with excellent design. Happy person to buy with confidence.

That one is lame, but something like that.

So what do you say?

BASS OUT

Link to comment
https://www.sau.com.au/forums/topic/91814-i-need-a-japlish-motto-for-my-parts/
Share on other sites

could always go with the classic Skyline motto of "In spartan air we made". Short, succint, and totally irrelevant... exactly what a japlish motto should be.

If you want to know how to make japlish/engrish, you go to:

http://babelfish.altavista.com/

You type in a phrase that makes perfect sense to you, and translate it from english to japanese...

then you copy and paste the result into the translate field again and translate from japanese to english...

Hey presto! instant japlish!

Here's one along similar lines to your original one that i prepared just then for you:

Original Phrase: "This Product is made to the highest standards and you should buy with confidence"

Translated to Japanese: "このプロダクトは高水準になされ、自信をもって買うべきである"

Translated back to English: "You can do this product to high level, you should buy with self-confidence"

Very low level stuff, but have a play around with it, you get some 'interesting' phrases out of good old babelfish :angry:

It reaches always and completes powerful outcomes and accurate .

just put sentences in to a translator, translate to japanese, then translate back..

oops

edit---

what AzzurrA said lol

Edited by sl!m

excuse me shan? I believe it's "we produced with spartan air"... Had to pull you up on the technicallity :angry:.. but what the hell does that actually mean? probably nothing..

In regards to your motto, just mix and match a few things from yahoo auctions.. bass junky's quality produce medieval times....

I occasionally see 'medieval times'...wtf??

Bit of Junkys bass. Give extreme power and the latent characteristic of air current to your car

Comes from

Bass Junkys Bits. Giving extreme power and air flow potential to your car

Bass Junkys bit perform outstanding power increases on your Skylines. The chicks will want to root you because of them.

The bit of Junkys bass increases the remarkable power of your skyline. The chick thinks that we would like to become fixed because of those.

Bass Junkys bit are fully sick and kick arse. These parts rock baby, yeah!

The bit of Junkys bass sufficiently is the anus of the sickness and the kicking. These parts it can obtain the baby, shakes!

and last for tonight

Bass Junkys radiator air guides help the air to flow through your radiator to increase the cooling potential of your car.

Gives:

The air guide of the radiator of Junkys of bass in order your radiator to percolate, helps the air in order to raise the cooling system.

Forget a logo and engraving. Remember thos ecool hologram cards you got in packets of chips as a kid...you knwo the ones that when you chanegd the angle at which you looked at them the picture would move.

Well just get one of those with your car stooopidly sideways on the DECA skidpan...god knows there is enough footage of you tearing it up:)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yes. Probably, given that there is only access from the bottom end of it, go with a drill bit. Don't start too small. 7 or 8mm is probably the right size. You want something that can make a big enough hole to do some damage, but not so bit that it clashes with the steel or binds up and breaks your wrist. A slow speed is probably a good idea too. Once the rubber is destroyed, you then have to get the crush tube off the stud, which will be the whole heat/oil/cutting exercise all over again, but this time with the need to strictly avoid damaging the stud (any further than the corrosion might already have done.
    • We replaced the connector just because we could and it was still there, once we swapped the injectors around it stopped. The injectors were something I had thoughts of replacing even before I first started the engine and in hindsight I should have 
    • Not too sure just yet, want to have a go at doing what I can myself, but to start with want someone to cast their eye over it tell me what needs doing to get it running and back on the road, so anyone with great overall knowledge would be ideal.
    • I personally would go with cutting out the rubber. Then deal with getting sleeve off separately. Rubber can be painful to cut, it loves to jam up cutting tools. I normally have success with drill bits, deburr bits, angle grinders, jigsaw, reciprocating saw, and never forget... fire. Obviously different tools won't work in all locations you're trying to work with, and you need to be comfortable with each. You personally may be happy slowly slicing it out with a razor blade, if you are, go for it with one too! Feel free to wait for others to weigh in also on their thoughts.
    • So ... I got everything disconnected and started dropping the frame. Three of the four mounts started to come down but the fourth one (the one with the nut that gave me all the trouble) won't budge. The inner metal sleeve stays up tight against the chassis rail although the outer part of the mount drops a bit (and can be levered quite a lot more) but it's just stretching the rubber bushing. So I reckon there's some serious corrosion inside the inner sleeve and holding it tight to the lug at the top of the bolt. Tried everything I can think of so far: penetrating oil, whacking the top of the sleeve to vibrate it and wedge a screwdriver blade in there. I also tried to turn the inner sleeve a bit by hitting it with a chisel at the bottom. It's stuck solid. What do you think about cutting the rubber with a blade so I can drop the subframe around it anyway. Then worry about getting the inner sleeve off after? Will that work? Is it gonna give me even more problems?
×
×
  • Create New...