Jump to content
SAU Community

Recommended Posts

Evening guys.. you don't know how much of a relief it is for the site to be back up and running..

Ok quick run down:

Got my car serviced on thursday last week..

The engine oil was changed to Pennzoil fully synthetic 10W40 I do believe.. before this the colour was still translucent but needed to be changed..

Anyways - on sunday went on the cruise up to Avoca via Old Pac and on the way home a couple of people started noticing that my car was blowing Brown smoke when boosting & probably @ high revs.

While I put this down to the car running rich - tonight I decided to check the oil as I hadn't looked since I had it changed.

Pulling the dipstick out I found it was almost jet black - and not translucent.

Intstant thought is Carbon (exchaust) has gotten into my oil and hence the colour of it.

My reasoning for this is a) I was running ~10psi all the way up but was finding the car would R&R so I only maxed it out at ~7psi by controlling throttle until it was time to leave and I put it to 0.6kg/cm^2 or approx 8psi which is what the standard solenoid runs. Because of the drive home we were on boost alot - it could have been forcing exhaust gasses into the oil and also possibly blow-by (i believe) where oil gets into the cylinder and hence the brown smoke..

now..

after having checked some other threads and also other sites - some people have commented that blackness or carbon can be a) the colour of the oil B) the oil cleaning crap out of the engine block c) exhaust getting into the oil some how (which is what I think has happened) probably because of the rings maybe??

I'm going to be changing my oil probably friday night or saturday morning with Motul 4200 or 8100 whichever I get my hands on first as I don't think the colour of the oil is good..

I need to get some feedback from people on what they think it could be.. The oil is not translucent anymore it's got a slightly grainy feel and is pretty black..

Any help would be great.. i'm quite worried as I think I might have f**ked a piston ring in the process of having high boost or driving relatively hard..

Thanks

Links

:P

Link to comment
https://www.sau.com.au/forums/topic/92559-black-engine-oil/
Share on other sites

are there any other problems with the way the car runs?

you should be able to tell if there is any fuel (exhaust) in your oil, you will be able to see it. Oil going black is no big deal. some oils go black quicker than others, some stay golden, some are purple so it's sometimes hard to judge just by the colour. if you really want to change the oil again, i wouldn't use turbolight 4200 it's a pretty crap oil. the 8100 is better. the penzoil that's in there is supposed to be very good. i know that is what my friend uses in his race motor.

my prediction is:

1. the smoke out the exhaust is just normal richness caused by the slightly higher than stock boost

2. the oil turning black is perfectly normal

oh, also how long was the previous service interval?

Link to comment
https://www.sau.com.au/forums/topic/92559-black-engine-oil/#findComment-1669659
Share on other sites

you might want to send a small sample away to get analysed. stick into a clean PET container ie plastic coke bottle, wrap tape around the screw top and package it well. most of the oil companes will do this for you, pretty sure duncan has had it done.

oil usually burns grey/white and fuel black, not sure what brown means. have heard various reports re pennzoil, a search should turn up a few comments.

not sure what 'car would r and r' means?

cheers

Link to comment
https://www.sau.com.au/forums/topic/92559-black-engine-oil/#findComment-1669827
Share on other sites

i use the same oil in my r32 (penzoil 10w40 semi-synth), goes black after about 3 or 4 weeks. This is ok, it means your oil is actually working, and absorbing carbon deposits.

Sometimes when going from mineral oil, to synthetic oils etc. the oil may have different additives which do a better job than your old oil. Might be a good idea to do another oil change if you're worried. But doesn't sound like there is a major problem or anything.

One sign of blow-by is popping out a dipstick. do you get this problem at all?

smoke could indicate a number of things. blown turbo springs to mind. Blue smoke indicates burning oil, black smoke indicates it's running rich.

Link to comment
https://www.sau.com.au/forums/topic/92559-black-engine-oil/#findComment-1669835
Share on other sites

id sugest changing brand of oil....

i use penrite and it takes a good while to go dark but that has heaps and heaps to do with the condition of the motor itself....for example if the previous owner never changed the oil and let the inside of the engine cake up with old dirt and oil deposits it will stay like that for a while....untill you consistantly do a few hot flushes of the oil.....

like run the car very hot and then drop the oil...and then flush more oil through and continue to do that untill the oil flows clean...

it sounds as though it has been poorly maintained in the past....

Link to comment
https://www.sau.com.au/forums/topic/92559-black-engine-oil/#findComment-1669860
Share on other sites

Thanks for the feedback people - after having spent all of last night and this morning both reading up and ringing people to find out different ideas i've formed some ideas, which can be seen in what you guys are also saying 2..

Bit of history first..

Car is 1998 - so it's only 7 years old, this is the first service it has had since owning the car - and the first oil change since it was complianced.

I think the boost pressure is possibly inrelevant to the issue..

from people i've spoken to as well as Eli i've got the following:

- Eli did a flush which should have cleared out anything in it (should have) - however i'm hesitent to believe this as some mechanics don't feel there is any need to do this.

- The oil that was put in when complianced was probably of average quality and may not have been doing much in the way of cleaning carbon in the engine and was letting sludge just sit there..

- Car has probably been doing street driving in slow traffic which tends to lead to more carbon/sludge buildup..

- When the Penzoil has been put in the Cleaning properties of this oil - which i'm sure are quite good - have started stirring up & loosening any buildup..

- Combining this with the fact that it was driven on the weekend relatively hard (not bouncing it off the limiter at all - never would) but still high boost sustained for increased durations it has proceeded to gather alot more crap from the inside than what it would under normal driving..

This leads to where i'm at.. an engine full of carbon particled oil..

We don't think there is anything wrong with the engine as the oil has not changed it's consistency, it hasn't got any sludge clumps in it and is probably still lubricating - while doing it's job which is to suspend carbon particles rather than letting them settle..

My current choice of action is to a) drop it back at the Mechanics and get him to take a look at it or b.) keep driving it for about 2 weeks to free up any other buildups and blocks than dump the oil, change the filter and put new oil in.

Currently this is what i'm leaning towards - and i'll probably be putting in Motul 8100 which is recommended on here..

Once i've done this i'll give it a week and monitor the oil..

now for the other things - brown smoke @ high RPM - we're puttin this down to running rich..

anyone got any ideas on what they think I should do??

Edited by Links
Link to comment
https://www.sau.com.au/forums/topic/92559-black-engine-oil/#findComment-1670256
Share on other sites

Once again - thanks everyone.. was very worried last night.. have calmed down a bit now.. as ImportAutoParts said - could be poor maintenence previously - or usage of average oil which wasn't cleaning it out properly..

I don't think it's blow-by as my understanding is this is caused by oil getting into the combustion chamber?? yes?? no?? if someone wants to explain feel free..

If this was happening it would be blowing smoke at idle possibly - I haven't seen any Blue or White smoke which would indicate coolant or water getting into it and also an oil leak - which makes me think the rings are still ok and the gasket hasn't blown..

Cheers

Links

Link to comment
https://www.sau.com.au/forums/topic/92559-black-engine-oil/#findComment-1670278
Share on other sites

yes compression test and/or leakdown test could be a good idea.

i really don't think it's anything. just your mind playing tricks on you :O

I'm sure Eli will happily take a look and make sure it's ok, or like you say give it a while and then switch to the motul if you like.

as for the smoke i'd say if it's happening whilst you are giving it some boot (under boost) then it's probably not blowby as the pcv is closed under boost (though i guess a little can still get through via the compressor inlet). i would bet it's just fuel. when i nail it in the GTR the car behind is practicaly enveloped in a cloud of smoke! when you are keen i'd say just go the ol' PFC or similar.

Link to comment
https://www.sau.com.au/forums/topic/92559-black-engine-oil/#findComment-1670622
Share on other sites

Oil colour???? If the oil is watery or has foreign fluid (coolant) then you have a problem. If its grey you have a problem. If you dump the oil into a clean pan and you can see paricles at the bottom of the pan thn you have a problem.

If your oil is black, well your oil is black. I wouldnt be at all worried. Mobil 1 use to come out of my engine black as the ace of spades. Castrol Formula R comes out of my engine black as the ace of spades.

I have no idea if these oils have a high detergeant level in them, but some oils do possess more then others. Oil primarily lubricates, but it also cools and cleans.

Quite frankly id be more concerned if my engine oil came out of my engine looking like new or transluscent after a few weeks or a few thousand kms. It may mean nothing, but could mean that all the very fine particles arent being captured in the oil, filters can oly do so much.

Again probably unrelated, but go grab some fine wet and dry and rub it on a metal surface. The resultant particles will appear to be black. The by products of combusiton/fuel etc are often black. The fact that your cooking oil goes black if you burn it/ repeatedly heat it. So why would you be alarmed if your engine oil turned black?

Just make sure its changed regularly with a good brand of oil, of the right viscosity, and if you are driving the car like a nutter at very high revs for sustained periods, well you may want to consider an oil cooler...but unless you have more power then std i wouldnt see that as a requirement.

Link to comment
https://www.sau.com.au/forums/topic/92559-black-engine-oil/#findComment-1670881
Share on other sites

Thanks Roy - I just got set off by a combination of factors.. however i'm not a fan of things that go from one extreme e.g. clean oil to quite black oil within the space of 5 days - considering he did a "flush" as well.. sure it'll be black - however I wouldn't have expected this to happen for a while - but maybe the weekend driving accelerated what normally happens..

Link to comment
https://www.sau.com.au/forums/topic/92559-black-engine-oil/#findComment-1670898
Share on other sites

My oil is like Roys, and it really dosen't take long to get to that stage. I change at very regular intervals 2000-3000km.

Compression or leakdown will confirm if its a problem with blowby. You might also want to throw it on a dyno and have a look at your AFRs.

Link to comment
https://www.sau.com.au/forums/topic/92559-black-engine-oil/#findComment-1670998
Share on other sites

My engine has a catch can and there is no blow by on my engine.

I have had two RB20s in my car now, and both have had plenty of flushes of very fresh fluid. Like a track day on a full sump, then the next weekend a new filter and sump for another track day. So th eoil would have done less then 400kms. Over kill? Most seem to think so.

But the oil is always pretty damn black. Even if the oil only had say 3,000kms or so of street use, it was always putrid looking.

So not saying its ideal, the way it should be, or indicaton that your car is in perfect condition. But i dont think its a cause for concern:)

Link to comment
https://www.sau.com.au/forums/topic/92559-black-engine-oil/#findComment-1671025
Share on other sites

Oil colour????  If the oil is watery or has foreign fluid (coolant) then you have a problem. If its grey you have a problem. If you dump the oil into a clean pan and you can see paricles at the bottom of the pan thn you have a problem.

if you you try to dump the oil and none comes out, then you have a problem :D

Link to comment
https://www.sau.com.au/forums/topic/92559-black-engine-oil/#findComment-1672767
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hey Dave, welcome aboard! Good to see another soon-to-be Stagea owner here. The wagons are awesome — plenty of space, still got that Skyline DNA, and loads of potential if you’re into mods. Definitely post up pics when you get it, everyone here loves seeing new builds. What model/year are you looking at?
    • See if you can thermal epoxy a heatsink or two onto it?
    • The other problem was one of those "oh shit we are going to die moments". Basically the high spec Q50s have a full electric steering rack, and the povo ones had a regular hydraulic rack with an electric pump.  So couple of laps into session 5 as I came into turn 2 (big run off now, happily), the dash turned into a christmas tree and the steering became super heavy and I went well off. I assumed it was a tyre failure so limped to the pits, but everything was OK. But....the master warning light was still on so I checked the DTCs and saw – C13E6 “Heat Protection”. Yes, that bloody steering rack computer sitting where the oil cooler should be has its own sensors and error logic, and decided I was using the steering wheel too much. I really appreciated the helpful information in the manual (my bold) POSSIBLE CAUSE • Continuing the overloading steering (Sports driving in the circuit etc,) “DATA MONITOR” >> “C/M TEMPERATURE”. The rise of steering force motor internal temperature caused the protection function to operate. This is not a system malfunction. INSPECTION END So, basically the electric motor in the steering rack got to 150c, and it decided to shut down without warning for my safety. Didn't feel safe. Short term I'll see if I can duct some air to that motor (the engine bay is sealed pretty tight). Long term, depending on how often this happens, I'll look into swapping the povo spec electric/hydraulic rack in. While the rack should be fine the power supply to the pump will be a pain and might be best to deal with it when I add a PDM.
    • And finally, 2 problems I really need to sort.  Firstly as Matt said the auto trans is not happy as it gets hot - I couldn't log the temps but the gauge showed 90o. On the first day I took it out back in Feb, because the coolant was getting hot I never got to any auto trans issues; but on this day by late session 3 and then really clearly in 4 and 5 as it got hotter it just would not shift up. You can hear the issue really clearly at 12:55 and 16:20 on the vid. So the good news is, literally this week Ecutek finally released tuning for the jatco 7 speed. I'll have a chat to Racebox and see what they can do electrically to keep it cooler and to get the gears, if anything. That will likely take some R&D and can only really happen on track as it never gets even warm with road use. I've also picked up some eye wateringly expensive Redline D6 ATF to try, it had the highest viscosity I could find at 100o so we will see if that helps (just waiting for some oil pan gaskets so I can change it properly). If neither of those work I need to remove the coolant/trans interwarmer and the radiator cooler and go to an external cooler....somewhere.....(goodbye washer reservoir?), and if that fails give up on this mad idea and wait for Nissan to release the manual 400R
    • So, what else.... Power. I don't know what it is making because I haven't done a post tune dyno run yet; I will when I get a chance. It was 240rwkw dead stock. Conclusion from the day....it does not need a single kw more until I sort some other stuff. It comes on so hard that I could hear the twin N1 turbos on the R32 crying, and I just can't use what it has around a tight track with the current setup. Brakes. They are perfect. Hit them hard all day and they never felt like having an issue; you can see in the video we were making ground on much lighter cars on better tyres under brakes. They are standard (red sport) calipers, standard size discs in DBA5000 2 piece, Winmax pads and Motul RBF600 fluid, all from Matty at Racebrakes Sydney. Keeping in mind the car is more powerful than my R32 and weighs 1780, he clearly knows his shit. Suspension. This is one of the first areas I need to change. It has electronically controlled dampers from factory, but everything is just way too soft for track work even on the hardest setting (it is nice when hustling on country roads though). In particular it rolls into oversteer mid corner and pitches too much under hard braking so it becomes unstable eg in the turn 1 kink I need to brake early, turn through the kink then brake again so I don't pirouette like an AE86. I need to get some decent shocks with matched springs and sway bars ASAP, even if it is just a v1 setup until I work out a proper race/rally setup later. Tyres. I am running Yoko A052 in 235/45/18 all round, because that was what I could get in approximately the right height on wheels I had in the shed (Rays/Nismo 18x8 off the old Leaf actually!). As track tyres they are pretty poor; I note GTSBoy recently posted a porker comparo video including them where they were about the same as AD09.....that is nothing like a top line track tyre. I'll start getting that sorted but realistically I should get proper sized wheels first (likely 9.5 +38 front and 11 +55 at the rear, so a custom order, and I can't rotate them like the R32), then work out what the best tyre option is. BTW on that, Targa Tas had gone to road tyres instead of semi slicks now so that is a whole other world of choices to sort. Diff. This is the other thing that urgently needs to be addressed. It left massive 1s out of the fish hook all day, even when I was trying not too (you can also hear it reving on the video, and see the RPM rising too fast compared to speed in the data). It has an open diff that Infiniti optimistically called a B-LSD for "Brake Limited Slip Diff". It does good straight line standing start 11s but it is woeful on the track. Nismo seem to make a 2 way for it.
×
×
  • Create New...