Jump to content
SAU Community

Building A Rb20det

carl h

By carl h,
in Engines & Forced Induction

 Share

Recommended Posts

carl h Proficient

carl h

Posted
Posted

well starting to look into options to build up the old 20's bottom end as power and age is starting to take its toll on the old girl.

i think that i am gonna go with arias pistons for the pistons, but not sure what kind of rods to source out?

who makes rb20 rods if anyone?

also i plan on working the rb20's head a bit, if anything to just clean it up and perhaps enlarge the valves a bit to aid in airflow.

thoughts please!

Link to comment
https://www.sau.com.au/forums/topic/93802-building-a-rb20det/
Share on other sites
EVLR30 Apprentice

EVLR30

Posted
Posted
well starting to look into options to build up the old 20's bottom end as power and age is starting to take its toll on the old girl.

i think that i am gonna go with arias pistons for the pistons, but not sure what kind of rods to source out?

who makes rb20 rods if anyone?

also i plan on working the rb20's head a bit, if anything to just clean it up and perhaps enlarge the valves a bit to aid in airflow.

thoughts please!

err rb30's are single ohc .. :D

DRFT32 Enthusiast

DRFT32

Posted
Posted

hey carl h...i have done pretty much what you want to do. i can say that the arias pistons are great.. haven't had any problems with them...they were nicely made with about 1 - 2 grams difference between the 6... so weight mathcing them was easy....

About the rods i dont know, i used the standard ones...just got them ballanced and weight matched....

in terms of head work i got the head ported and polished with 1mm oversized valves..you will find that ca18 valves are perfect for it..they are 1 mm larger than standard rb20 ones and fit with no trouble...

hope that helps....

Aaron

carl h Proficient

carl h

Posted
  • Author
Posted
hey carl h...i have done pretty much what you want to do. i can say that the arias pistons are great..  haven't had any problems with them...they were nicely made with about 1 - 2 grams difference between the 6... so weight mathcing them was easy....

About the rods i dont know, i used the standard ones...just got them ballanced and weight matched....

in terms of head work i got the head ported and polished with 1mm oversized valves..you will find that ca18 valves are perfect for it..they are 1 mm larger than standard rb20 ones and fit with no trouble...

hope that helps....

Aaron

spot on there sir spot on!

as far as the valves, the standard ca18 valves will fit into the head? and if so 1mm will certianly aid in airflow into the motor.

how much power are you making with standard rods, everyone seems to have gotten in on a betting pool on my car when it comes to the motor's internals......

cheers!

DRFT32 Enthusiast

DRFT32

Posted
Posted

in terms of power i havn't done a power run as yet..i am stil adding bits a pieces and changing things around. it made 138 rwkw before it all and this is auto so would be a bit more if manual.

It goes a sh1t load better since i did all of the stuff...the full potential hasn't been reached yet but from the mods i have done and from what i seen other people get i would say that it would have to be easy over 200rwkw...but it has alot of variables...you could put arias pistons in, other rods , over sized valves etc and still have the same amount of power that you started with or very little more...

it will aid greatly if adding biggger turbos and more boost etc

yes the valves do fit..they are in my car now !!

i guess it comes down to what you want to achieve with the engine on whether it will be worth it and whether it make a worthwhile difference.

And whether to get aftermarket rods.....

what do you want to achieve ???

blind_elk Grand Master

blind_elk

Posted
Posted

My first recommendation would be to install the pistons for the RB23/24 kit (but leave the stroke the same). That way, you get a bit of capacity, but better you get a bit of off-boost compression (I think I calculated 0.5 increase in C/R). That gives you 9:1 C/R; considering the racing GT-R's we had in Oz ran 9.2:1 and 1.8bar, I think the RB20 will cope.

DRIFTER - if you stick a head of a larger capacity engine onto a smaller capacity block, you LOSE compression. Apart from the fact that a RB30 head will not fit comfortably on a RB20 block. And why would a single cam head flow better than a twin cam head. I think you are thinking of the RB25DE(T) head onto a RB30 block.

DRFT32 Enthusiast

DRFT32

Posted
Posted

ebola...i am still runnning standard cams...but am running os geiken adj cam gears... waiting for gtr cams to see how they wil go with chipped ecu..there was a big thread about it a while ago....in terms of rev limit i have no idea....but with 20's power almost alwasy drops off after about 6800 - 7000 RPM so.....

jaik Mentor

jaik

Posted
Posted

Theres also a mass of threads about GTR cams NOT working in RB20 due to the ramp rate being greater compared to the standard 20 cams, and therefore the cars that have had GTR cams installed are struggling to idle. I would investigate those threads before throwing in the GTR sticks.

JK

carl h Proficient

carl h

Posted
  • Author
Posted

well on my car i have tomei 260/8.8 cams with greddy gears and a gt30r turbo, so it is a bit laggy but pulls like a cut bastard to redline (8.5k).

i mainly want to build the engine not for outright power but for reliablity, i plan on keeping the car round for another few years and i cant imagine that the stock internals are going to keep up with the 450bhp the car puts out on high boost.

  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • PranK
      Blue slip

      By PranK · Posted

    • GTSBoy
      Ethanol Content Sensor - Always at 11%?

      By GTSBoy · Posted

      But seriously, can we ask for the results of the "tip a bottle of metho into a nearly empty tank" experiment?
    • GTSBoy
      Blue slip

      By GTSBoy · Posted

      Hang on. Let me get this straight. The desire is to have coilovers, BC in particular, to be MORE comfortable on Sydney roads than stock suspension? Well, that's obviously not right. BCs have crude damping design at the very best, and typically hard spring rates. BC stands for Billy Cart. And then, the desire is to put in some shitty old worn out stockers, to get it blue slipped and then put the BCs back in? And then.....what? Not worry about getting pulled up by the Plod? Because you seem to have raised a worry about paying for engineering (which actually does solve all your legality problems) and still getting pulled up.... but the only problem there is that if/when that happens you have to show your paperwork at the inspection station. Whereas, if you just swap in borrowed shitty old stockers to get it slipped now, and then you get defected in the future, you have to go find more shitty old stockers then too. You course of action looks like this set of options: Buy brand new stock type dampers, and springs. probably cost a bit more than $1k all up, but will last for the remaining life of the car. Put them in, pass inspection, drive on them forever more. Hell, they could even be really nice Bilsteins and Kings or other lower&stiffer springs if you wanted. Get the car engineered as is. ~$1k. Buy new Shockworks coilvers (or MCA) and also pay for engineering. You're spending a lot more here. But these will be the best things that you could drive around on.
    • Dose Pipe Sutututu
      Blue slip

      By Dose Pipe Sutututu · Posted

      Might be worthwhile hitting up Facebook's groups, I know most of them contain terrible people and scammers - however you might be able to find someone that's in Sydney with factory suspension you could purchase and/or hire. Just do not send any form of money anywhere, in person cash only.
    • Stringycheese
      Blue slip

      By Stringycheese · Posted

      Thanks @Duncan Ride height is fine. I think it's almost stock tbh. Happy to share a pic. I don't actually have a regular mechanic as haven't lived in Sydney too long. Could you or anyone recommend any shops in Sydney?
×
×
  • Create New...