Jump to content
SAU Community

Recommended Posts

Okay could be a number of models,

Series 1 VL turbo block

Series 2 turbo or non turbo

Any series skyline block

It is good as the oil return and high pressure are already there, so from that point of view it is slightly better than doing some extra work. However some people believe the earlier holden blocks are better as they are cast from better grey iron, however I believe it is a myth!!!

as far as i know there was only the one rb30 block brought out by nissan... got any numbers??? it could be a vlturbo motor if its got the extra galeries drilled out for the turbo or maybe (not sure) could be out of one those m30 skylines they were twin cam (rb20) head but n/a

The most important part of the rb30 block for our twin cam conversions I think is the lack of a machined surface to mount the tensioner on.

Looking at the front of the block you will see two drilled and tapped holes where the tenioner studs screw in to.

Both must have a flat machined surface. I believe its the series 1 blocks that don't have the right tensioner location machined flat.

I've got pics some where of what to look for.

Don't go off what car the motor came out of, these cars are old now and often than not you will find a series 1 with a series 2 motor but a series 2 with a series 1 motor. :P

This is a genuine turbo block that was removed from an 1988 Holden Commodore BT-1. If it isn't the original engine from the vehicle I would be very suprised. Pictures are worth a thousand words so here's my essay :P

100_5597.jpg

100_5599.jpg

As you can see one stud needs to be drilled out in the second image.

Bigsully84,

That block is perfect.. As you can see the right stud hole has a flat machined area.

The blokes that don't have this simply have a hole with no flat machined area.

So it will be fine to use as an RB31DET conversion?

I am wanting to buy it but thought I would get advice from the people on here.

if you don't have the flat machined surface there you will have to do this:

DSC00177.jpg

DSC00174.jpg

which is really not a big deal at all, considering you've either bought the drill bit and tap yourself already, or you're getting a machine shop to do it. the main things to get on the block are the provisions for the oil and water lines, which are a bastard to tap yourself.

everyone with an RB25 or 26..... have you seen how close the standard tensioner and idler pulley come on the twin cam RB's? it's pretty much exactly what you'd get if you used the two pre-drilled tensioner locations on the RB30 block, on either side of the welsh plug there.

as far as being worried about the belt touching because it's too close together, that is pretty much a non-existent danger. if it's not enough that the OEM engine uses a timing belt setup which comes that close together without problems, consider how much the slack side of the belt (inlet cam side of the belt) would have to flop to touch the reciprocal side of the belt moving the opposite direction. a properly tensioned cam belt simply cannot move that much, even under extreme loads (giant cams on rapid RPM changes).

if i had a series 2 block to start with, i would have used the two lower tensioner locations for simplicity and cost reasons. as it was i had to do what the pictures show above, which is quite a good setup as far as i can determine.

I paid $150 for a running motor that had the head ripped off and sold. At a wrecker.

I found the larger wreckers sold them for $200-$300, the smaller little wreckers only wanted $100-$150.

Mine came out of a arse ended VL wagon.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Price seems pretty good to me. Also seems a hell of a lot cheaper then buying another vehicle that only ever gets used for towing.  I'm a long way from you mate, I'm a couple of hours out of Brizzy. 
    • New [400]Z, they're available in manual and you don't have to worry about parts scarcity. 
    • Just planning to have the wiring neat and hide as much as possible.
    • The sodium acetate, mixed with citric acid, doesn't actually buffer each other. Interestingly though, if you used Sodium Acetate, and acetic acid, THAT becomes a buffer solution. Additionally, a weak acid that can attack a metal, is still a weak acid that can attack a metal. If you don't neutralise it, and wash it off, it's going to be able to keep attacking. It works the same way when battery acid dries, get that stuff somewhere, and then it gets wet, and off it goes again breaking things down. There's a reason why people prefer a weak acid, and it's because they want TIME to be able to be on their side. IE, DIY guys are happy to leave some mild steel in vinegar for 24 hours to get mill scale off. However, if you want to do it chemically in industry, you grab the muriatic acid. If you want to do it quicker at home, go for the acetic acid if you don't want muriatic around. At the end of the day, look at the above thumbnail, as it proves what I said in the earlier post, you can clean that fuel tank up all you want with the solution, but the rust that has now been removed was once the metal of the fuel tank. So how thin in spots is your fuel tank getting? If the magazine on the left, is the actual same magazine as on the right, you'll notice it even introduces more holes... Well, rust removal in general actually does that. The fuel tank isn't very thick. So, I'll state again, look to replace the tank, replace the fuel hanger, and pump, work out how the rust and shit is making it past the fuel filter, and getting into the injectors. That is the real problem. If the fuel filter were doing its job, the injectors wouldn't be blocked.
    • Despite having minimal clothing because of the hot weather right now, I did have rubber gloves and safety glasses on just in-case for most of the time. Yes, I was scrubbing with my gloves on before, but brushing with a brush removes the remaining rust. To neutralize, I was thinking distilled water and baking soda, or do you think that would be overkill?
×
×
  • Create New...