Jump to content
SAU Community

Recommended Posts

I've just bought a n R32 GTS-T which has a remote oil filter kit and i want to know if there is a correct procedure to change the oil and filter ? Any help would be great  thanks ! :)

I was asking because the lines to the remote filter would be emptied of oil. I thought that this may have been a concern ! I've done plenty of oil changes before, but none with a remote filter.

I was asking because the lines to the remote filter would be emptied of oil. I thought that this may have been a concern ! I've done plenty of oil changes before, but none with a remote filter.

ah yep... sorry for the cynical reply there.. was in a bad mood!

it won't be a problem, when you start the car, oil will run through the lines and fill up the filter.

when car is off, oil drains out of the filter/lines into the sump anyway.

ah yep... sorry for the cynical reply there.. was in a bad mood!

it won't be a problem, when you start the car, oil will run through the lines and fill up the filter.

when car is off,  oil drains out of the filter/lines into the sump anyway.

Cheers guys, i feel better knowing motul is in the sump now ! Average oil temp is down about 4 degrees.

  • 2 weeks later...

I'm needing to change my oil too (already put about 5000km on it since I bought it two months ago!) actually but I haven't tried it before, but going by the description I found on the forum I reckon I should be right.

Anyway, just a question, how do I tell a remote filter or if I've just got a regular filter and more importantly, which oil filter do you guys use??

Cheers

AF

I'm needing to change my oil too (already put about 5000km on it since I bought it two months ago!)  actually but I haven't tried it before, but going by the description I found on the forum I reckon I should be right.

Anyway, just a question, how do I tell a remote filter or if I've just got a regular filter and more importantly, which oil filter do you guys use??

Cheers

AF

The standard filter is a Z145A, Ryco or K&N are both good or you can get a genuine part from Nissan. I've got a Greddy filter on my remote set up. The standard filter will be down on the side of your engine block. A remote filter will usually be found up near the top of the right shock tower. Check out this attatchment.....

post-24581-1132745579.jpg

Just my 2 cents........

I have a drain valve installed in one of the oil cooler lines and when I do my oil changes I drain as much as I can from the cooler. I've found that most of the oil does NOT drain back to the sump unless your oil cooler AND lines are mounted above the level of the filter boss on the engine block. Thusly I put a drain valve in place to get more of the old oil out during a change.

When I re-fill the sump with oil, I disconnect the ignition control module and crank the engine over for about 5 seconds to pump some oil through the system, then re-connect the ignition and start her up. Oil pressure comes up much quicker so there's less chance of hurting the engine. Yes, you may very well reduce the life of your starter motor but a starter motor is a lot cheaper to replace than a set of bearings :P

The standard filter is a Z145A, Ryco or K&N are both good or you can get a genuine part from Nissan. I've got a Greddy filter on my remote set up. The standard filter will be down on the side of your engine block. A remote filter will usually be found up near the top of the right shock tower. Check out this attatchment.....

ahh i see :P

thats a nice engine bay dude :D

very clean lookin sharp

like the carbon fibre :P

The standard filter is a Z145A, Ryco or K&N are both good or you can get a genuine part from Nissan. I've got a Greddy filter on my remote set up. The standard filter will be down on the side of your engine block. A remote filter will usually be found up near the top of the right shock tower. Check out this attatchment.....

Thanks SNISMO, got to say that's a pretty nice engine bay! Good Photo too really explaines everything :rolleyes:

  • 2 years later...

I know this thread is old but I thought I'd post here since it's a good thread. Just had the car service, has a remote oil filter. Now they ended up putting about 5 and a bit litres of oil into the engine. Brought then a 4ltr and 2ltr bottle of Motul Chronos 300v. Now I thought the maximum to fill would be 4.5, but they basically said there should not be an issue with overfilling it with oil due to the extra lines running to the remote oil filter and oil cooler. Sounds fair enough, just wondering if it's true. Just most of the other times, Just used a normall 5ltr bottle or 4.5 litre bottle of oil.

I had a GReddy oil relocator fitted to my car last week and with all the extra crap in the gtr we couldnt find anywhere neat to mount it on the strut tower like most people do, we ended up fitted it below the engine right next to the sump drain bolt with a little custom bracket.

I'm glad it ended up this way because their would be nothing worse than having a relocator fitted only to have oil piss all over the place because it is mounted upside down, that kinda defeats the whole purpose of it, if I wanted to make a mess I would have just left it where it is.

smear some oil on the rubber seal of the filter, then screw it on as tight as you can with your bare hands. if it leaks, tighten a bit more with an oil filter wrench ($10) but it shouldnt have to be very tight

dude...I am glad that I am not doing your oil changes....In every oil filter change I have ever done its always been done with one hand only.There is no need to lock them up that tight.Using two hands to tighten up is a bit too much ...but using a wrench to tighten it???? first time I have ever heard of anyone doing this.

I had a GReddy oil relocator fitted to my car last week and with all the extra crap in the gtr we couldnt find anywhere neat to mount it on the strut tower like most people do, we ended up fitted it below the engine right next to the sump drain bolt with a little custom bracket.

I'm glad it ended up this way because their would be nothing worse than having a relocator fitted only to have oil piss all over the place because it is mounted upside down, that kinda defeats the whole purpose of it, if I wanted to make a mess I would have just left it where it is.

hey I like your idea very much.Sure they look good in magazines mounted upside down but I have always wondered how they are changed without making a mess..Any chance of putting any pictures up ?

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That still isn't a lot to go on. I don't have a Y50 Fuga Head Unit wiring diagram. I can say that a lot of nissans of that age shared head unit plugs, so if you are in Australia something like this would probably help: https://aerpro.com/app091# You plug that into the car loom, then either plug the head unit ISO into that (if it has ISO), or you buy and ISO adapter harness that you wire in. Bit of stuffing around, but once you have ISO its easy to change things in future.
    • It is a kunfine Android screen . Does anyone know the wirering diagram of the fuga ??
    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
×
×
  • Create New...