Jump to content
SAU Community

Gb: R33 Gts-t And Gtr And R34 Gtt Radiator Guides


Recommended Posts

Hey ppls.

As many of you may already know, I seem to be the Radiator guide king.

I've just drawn up the R33 GTR and R33 GTS-T Radiator guides to be made from Aircraft Grade 1.0mm Aluminum.

They will be of the same high quality as my R34 GTT guides and will cost pretty much the same.

I'm bending up the prototypes in the next week or so, but would like to get an idea of numbers of how many people would like them.

The price will be close enough to $80 + Freight, but the more people, the merrier.

SO, Who's in?

R33 GTS-T

2BNVS...........................berkeley nsw 2506..........................PAID

Dezz..............................Hoppers Crossing 3029, Vic.............PAID

bilbo117........................................................................

....Paying Monday

Dynamix

GTS-T V-Spec..........Balcatta, WA 6021.................................PAID

Mavric.....................Melbourne Pick Up.................................PAID

Trust33....................Address Received.................................PAID WITH ANODISING

ZXFIRE....................Sydney, 2170, N.S.W............................PAID

GTRgeoff.................Melbourne Pick Up.................................PAID

Greg.......................Melbourne Pick Up.................................PAID WITH ANODISING[/

Freeman..................Newcastle, 2287, N.S.W........................CONFIRMED

Babia......................Melbourne Pick Up.................................PAID

Sydneykid...............Sydney, NSW, 2234

Deceeve..................Mt.Pritchard, NSW , 2170......................CONFIRMED

wolverine................NSW..................................................PAID

Lordsnipe................West Perth, 6005, W.A.........................PAID

Alpine Stars.............Perth, 6000, W.A

(B1) MR_fanny.........Melbourne Pick Up...............................PAID

Trick x 2..................Hope Valley, SA, 5090.........................CONFIRMED

Total 22

R33 GTR

GTRgeoff.................Melbourne Pick Up.................................PAID

Cooper....................Morphett Vale SA 5162..........................PAID

Trick........................Hope Valley, SA, 5090...........................CONFIRMED

Total 2

R34 GTT

darn756

woldo......................Kings Park, 3021, VIC, standard Bar.............PAID

Mr Sniper911...........Loxton, 5333, S.A, STD Bar..........................PAID

GT25T.....................cabramatta, 2166, NSW, Nismo Bar..............PAID

kralster...................Victor Harbor, 5211, S.A STD Bar...............PAID

SKY 34.....................Cannington, 6107, W.A BOMEX Bar.............PAID WITH ANODISING

JapanDyno x 10..........Germany, Pick Up when in Aust

HLT4Eva...................Melbourne Pick Up.....................................PAID

Total 16

BASS OUT

  • Replies 520
  • Created
  • Last Reply

Top Posters In This Topic

id be in.... question though, how they normally come with the hole for the bonnet latch can u make one thats flush like no gaps for the latch since i dont have mine anyway?

ben...

Is there a thread or perhaps you can tell me yourself:

What are the benefits of such guides?

Is there a real-world difference?

Is there a quantitative performance increase (eg dyno/400m times)?

Edited by Wink

Okay,

What the air guide does is stops the air from going through your grill and up over the top of your radiator.

It forces air through the radiator and increases the cooling capacity of your radiator.

Also, it looks cool and gives you somewhere to put stickers.

post-6399-1132289250.jpg

Hey Bass.Do they sit good on aftermarket front bars.

My bar is aftermarket and the headlight is missing the plastic mounts that the stock grille usually sits on.And because of that there really is no place for the front of the deflector to sit.

Would it be easy to make a mount for one of these myself??

answers

They bolt onto the radiator support panel, so there's no real problem with aftermarket front bars.

My experience with the R34 GTT, is that the brs are very similar with only slight differnces between the stock and aftermarket bars.

Nothing a quick blast with an angle grinder or a hand file can't fix.

I have designs currently for R34 GTT with Nismo, stock and aftermarket front bars.

I have designs for R33 GTS-T and GTR

I have not yet got R32 or R31 bars.

These I will look at soon.

Oh, and you need to tell me what model of car you have and whether you have stock or aftermarket front bars.

So like, R33 GTS-T SII stock bar.

or R33 GTR series III stock bar.

Cheers

Pete

what are the differences between your product and the UAS one or are they equivalent?

also, if there is enough interest would you be interested in making a guide that goes the whole length of the engine bay? ie covers the tops of the headlights as well. i'll try and dig up a pic if you're not sure what i mean. it may be too much mucking around to make it though.

Thanks

Greg

Yep, they will be equivalent or better to the UAS. I'll make them as best I can.

Greg. I've thought about making the extended version, but doing it in Aluminum will be very trickey, and difficult/expensive to send. Making it from say FRP or Carbon Fibre isn't what I'm into. Although I know it can be done this way, I'm no expert in it.

There isn't much airflow benefit in doing it that way, but it sure looks good!!

BASS OUT

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...