Jump to content
SAU Community

Recommended Posts

Hi Jim,

I find these results amazing, 20awkw is a substantial increase!

I have booked my final tune with crd for next week...I will post my results here for everyones perusal.

Regards,

Marko.

Hey Guys,

Here is dyno sheet of a R33 GTR with a new engine we built with R34 N1 turbochargers with before and after of 98 and 100 octane shell fuel.

Car is used for circuit only.

CRD

  • 2 weeks later...
ive had my safc tuned for 98 octane.. if i use this extreme stuff would i REALLY need a retune?

Only if you rev the engine out, or value your pistons' life spans.

The fact that higher RON level means you can run more timing isn't as important for the retune, but the fact that its oxygenated means your engine will run lean comparable to your 98RON tune is why your current setup may not be good for the engine.

If you've got it tuned close to the edge on 0% ethanol fuel, the E5 Optimax Extreme might push it to a point where you get detonation.

This is big I actually calculated 41 extra four wkw for extra 2 octane points. Must have had more timing and maybe more boost added to do this?

We did same on S15 yesterday and made almost 20rwkw with a bit more boost and timing.

There is a question mark with the Ethanol in it effecting injector seals as well as early model injector design and electrolysis. But hey I am going to use it and guess it should be ok or they would not release it, or are we all test pilots?

well, i had a sip of it yesterday and it tastes no where near as good as bp ultimate. true.

It certainly looks like a good option for race use. Much cheaper than the options from elf etc.

well, i had a sip of it yesterday and it tastes no where near as good as bp ultimate. true.

It certainly looks like a good option for race use. Much cheaper than the options from elf etc.

full tune and comparo to C16 coming soon....keep you posted

full tune and comparo to C16 coming soon....keep you posted

I used it in my Slot Car at Wakefield yesterday and no problems and car felt strong all day.

I've filled half a tank yesty.... just a question tho... I have a stock ecu.. how do i reset it... and.. do i need to?

Reset does jack....

I had mine on the dyno ~3years ago, did a few little tests - pod vs stock airbox, ecu reset. All showed a zero increase in power anywhere in the rpm.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm selling my personal race car. 1992 BNR32 Skyline GT-R About eight years ago the engine developed the dreaded low oil pressure problem. I removed it and found the issue. However shortly after I moved half way across the country, moved my work shop, bought a house, got married, then moved my shop again to it's permanent location for the time being. in turn I do not have the time to race this car as it should be. In turn the engine I built for this car will end up in my street car and this car I hope finds a home with someone who can use it to it's full potential. The roll bar was built by Jason Noren Fabricaiton in Pomona California to SCCA and NASA Specs. The car used to compete in redline time attack and global time attack enthusiast class. It also has a fire suppression system.  The car is with me at my workshop in Kyle Texas, USA. Shipping it is no problem, I can personally deliver the car to the port of either Houston or Los Angeles. Any other port depending on where it is may require transport but we can always work that out.   The chassis itself is rust free, rear quarters and under fenders are free of any rust so it's a very solid foundation for anyone who wishes to move forward with it. As posted and at the asking price of $20,000 USD the car includes all of the following;   All OEM Body panels, front fenders, rear bumpers etc.  OEM Nissan Projector headlamps (Pictured N1 lamps were removed) OEM Nismo Side Skirts / Extensions OEM Rear Spats  Front & Rear Subframes are installed car is full roller Rear Subframe has Cusco Camber Arms, Whiteline HICAS Elimination Front Subframe has Whiteline tension rods and whiteline Sway bars w/ endlinks.  Buddy Club N1 Coilovers All chassis wiring and engine wiring is in tact. Attessa System is fully in tact and was functional before engine removal.  BCNR33 GT-R Brembo Brakes F+R with Endless MX72 Plus Pads, DBA Rotors & Stainless Steel Brake lines Billion Racing Radiator Billion Radiator Hoses Fluidyne Engine Oil Cooler Accusump System (trunk Mounted) 5 Speed Transmission w/ Transfer Case F+R Prop-shafts Rear Differential With rear Axles.  Nismo Gauge Cluster Nismo Clutch + Flywheel   Essentially what is needed to make this car running and driving again is as follows: A working Engine, an ECU, and time to put it together. The price posted is or best offer as I am willing to remove some components to accommodate price to a certain extent. If any serious buyer wants full detailed pictures, videos, or any questions I'll be happy to answer them. I believe this car is priced to move quickly considering it's a rust free and very straight chassis but always open to fair negotiation.  I can be contacted via phone or email. (+19517081648) email is juan@bardabe.com   
    • So...to my (and my mechanics doing the swap) surprise...the oil pan from NEO engine does not fit 100% and needs to by modified like this: It is not a huge problem but in the future i want a "proper" oil pan. So question is...what different oil pan can i get to fit without any problems and modification? Thanks! 
    • Some more info I found.  These are the last entries Yoshikiyo Fujii made on his blog before he passed away in 2009: http://blog.livedoor.jp/fujii_dynamics/ And finally this is where the workshop was situated:  https://maps.app.goo.gl/HhTPtHzt3WVcBTiEA  
    • shit boxes, kids, and daily drivers are all welcome
    • Cam seals go hard. It's a very old car.
×
×
  • Create New...