Jump to content
SAU Community

Sauwa Chrissy Crooze 05 Sunday 11th December 2005


Recommended Posts

  • Replies 98
  • Created
  • Last Reply

Top Posters In This Topic

Don't think i'm coming anymore, I've been talked into doing a modelling comp instead haha. I've never done one before :D kinda freakin out....

Hope you all have a good time, guess i'll meet ya's at the drag night instead :)

I cant go ladies and gents my car got broken in to and busted up abit and work stuff stollen

has realy f**ked my life up at the moment

the liner is ok tho they f**ked up the bunky but i am in deep shit

sorry

james

Hey! Whats the dillio? I went down and there (there at about 12:40pm) and nobody was there :)

I saw 4 Skylines (3 R33's and a GMG R32 GTR) drive past and not pull into the truck stop and then I just drove home at 1pm.

Was I at the wrong truck stop?! :)

when we finally caught up with the rest of the cruise... that commodore was insane!

edit: i thought i couldnt see your car there topaz.. maybe you should have followed those skylines where ever they went? :)

when we finally caught up with the rest of the cruise... that commodore was insane!

edit: i thought i couldnt see your car there topaz.. maybe you should have followed those skylines where ever they went? :(

one continued on down Kewdale Rd, two continued on down Abernethy and the other went the other way down Abernethy :):)

I went for a drive down Kewdale and Abernethy and couldn't find any other truck stops....did everyone go to the truck stop on the corner?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...