Jump to content
SAU Community

Recommended Posts

Annoying problem, my R32 GTR dash and rear light fuse keeps blowing.

Pulled out the existing and swapped in a new 10A fuse, blew it straight away.

Anyone have any ideas as to what would cause this?

Would a short circuit somewhere cause this to happen?

My alarm was installed reasonably recently so there has been someone in there playing around with wires :P

Incidentally, I also noticed that for the starter signal fuse there is a 15A instead of the 10A on the diagram, and a 20A for the hazard lights instead of 10A.

Maybe replace the incorrect fuses with the correct ones.

I know this is a sh*t job but you may need to look at the connections for the alarm system. Maybe they left a wire naked and its touching the frame of the car, or something else.

Look for dodgy wiring, close up lose ends. Pretty much do an inspection of your car. Some places may be... near ECU, where your headunit is, near battery, anywhere where someone can play with and stuff up.

If those fuses that are incorrect, I would change them IMMEDIATELY. They will blow the component that its linked too.

Thanks mate.

-Arbess

> If this happened right after the alarm install, the installer could have mistaken the lamp wire as a ground. It is easily done, i accidentally did this to my mates car, while installing a stereo head unit. When the lamps are off the wire measures as ground, but when you turn the lamps on the fuse blows as wire becomes live.

> If you recently installed a head unit - read above :P

> Always replace the fuse with it's correctly marked rating. Fuses are there to protect the wirng, the last thing you want to do is to rewire you car.

Hope that helps

PS: If you are uncapable of disconnecting your all power wires to your alarm (inc ground), then go back to your installer, as them to disconnect it, replace the fuse and test the lights.

i had this problem in my 32,

found an un termintated wire behind my headunit with exposed wires, was earthing and blowing my fuses.

check back there for exposed wires plus what the other guys said

good luck

Thanks guys.

Someone also broke into the car recently and pulled out the ashtray to, i assume, get to the head unit. Maybe theyve pulled on the wires there and thats caused something.

Actually, on a reasonably hot day recently, my alarm went off twice for no reason - never done this before. This was around the same few days that the problem happened.

Bring on the pain - time to fire up that freakin' multi-meter and get my electrical tape out :D

I had the same problem but with my R33 Gts-t.

The rear light was in the "unlock" position and kept moving in and somehow caused the circuit to short and blow the fuse.

Maybe have a look at the taillights make sure its all fine?

This story ends happily..... managed to find the problem last night, one of the 40 thousand wires in behind my head unit / aircon / guages was obviously shorting somewhere, pulled that apart and tightened up all plugs and re-arranged the wires and bingo - no more popped fuse.

Whent the $%&$ broke in they must have had a play around.... never trust reservoir, melbourne.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah i found that alot of parts can be wrong or "very" hard to get the real right one. I already bought some brakes years ago on me "old" GT calipers and they were wrong too 😄  I told them too. Even send them pictures...but they said "EBC catalogue has them on my car... So i dont know what their answer will be. I call monday them and let them know that they are really not on my car. If they were they would be already on a car...
    • Welcome to Skyline ownership. Yes, it is entirely possible parts websites get things wrong. There's a whole world of inaccuracies out there when it comes to R34 stuff (and probably 33 and 32). Lots of things that are 'just bolt on, entirely interchangable' aren't. Even between S1 and S2 R34's. Yes they have a GTT item supposedly being 296mm. This is incorrect. I would call whoever you got them from and return them and let them know the GTT actually uses 310mm rotors. Depending on where you got them from your experience and success will obviously vary.
    • Hi...a bit a "development" on the brakes. I spoke to the guys where i get brakes from...and they are saying that 296mm EBC are for R34 GT-T. I then went to their site: https://www.ebcbrakes.com/vehicle/uk-row/NISSAN/Skyline (R34)/ and search for my car(R34 GT 1998 - it has GTT brakes) and it show me this USR1229 number and they are rly 296mm rotors... So now iam rly confused... The rotors i have now on the car are 310mm asi shown... So where is the problem? Does the whole EBC got it wrong or my calipers are just...idk know what?  
    • Oh What the hell, I used to get a "are you sure you want to reply, this thread is XX months old" message. Maybe a software update remove that. My bad.
    • This is a recipe for disaster* Note: Disaster is relative. The thing that often gets lost in threads like this is what is considered acceptable poke and compromise between what one person considers 'good' looks and what someone else does. The quoted specs would sit absurdly outside the guards with the spacers mentioned and need  REALLY thin tyres and a LOT of camber AND rolling the guards to fit. Some people love this. Some people consider this a ruined car. One thing is for certain though, rolling the guards is pretty much mandatory for any 'good' fitment (of either variety). It is often the difference between any fitment remotely close to the guards. "Not to mention the rears were like a mm from hitting the coilovers." I have a question though - This spec is VERY close to what I was planning to buy relative to the inboard suspension - I have an offset measuring tool on the way to confirm it. When you say "like a mm" do you mean literally 1mm? Or 2mm? Cause that's enough clearance for me in the rear :p I actually found the more limiting factor ISNT the coilover but the actual suspension arms. Did you take a look at how close those were?
×
×
  • Create New...