Chris Rogers

on a 4 button one it is the light or boot release button pressed twice.

for me $1500 and 1.5 days done properly. the cate is no longer made. I'm waiting on the new version. speak to security in motion for autowatch in sydney.

will do.

nope separate sensors. I have a trick that I can use that WILL combine them but it involves another unit. know of a 10 disc dvd unit but I'll have to see if it is still available.

I'll email it to you. waz, yep giot it.

garmin is RF based. no IR beam. the tv is IR. as for IR placement for the DVD unit - your call where it is placed. I have been putting them INSIDE the AC display to hide them - some are too big to do this though. any of the IPOD ones I do that is where they are. (oaksey if you are reading this that is where yours is.)

yep its a fun job. I want your old radio controls harness is wired through the clockspring but terminates on the wheel side inside the column shroud - you need the wiring diagram to pin it out and get the wiring through.

room will be the problem on that one. glovebox is VERY doable OR centre arm rest OR if you want to remake the rear seat centre section it would fit there. in dash - not easily. as for quality same as the 8000.

seen that one before. have a chinese supplier hounding me to buy them. roughly the same price. no market (not big enough) for me to justify buying 100 at a time.

ok: undo battery negative lead.(remember to reset your TV.) remove cover caps from side of steering wheel. remove two tamperproof (think they are t30) remove air bag and pop clip out of the bag of the plug pull plug out of air bag and set that aside. disconnect horn wire (yellow wire that runs to steel frame.) undo the two torx bolts that are now visible (t30 or t35) and remove assembly, careful with springs undo 19mm nut but do not take it off. unplug steering controls and send to me wriggle wheel until it comes off. remove 19mm nut and remove remove 4 phillips screws and remove the rear plastic shroud, this is clipped on. remove 4 screws from SWC and blank panel. when you put it back together route the cruise wiring across the top of the rear cover so it doesn't foul on the horn assembly. ring me if you get lost.

noel, nahhh. shows how many of these cars I actually work on. found a siren for you btw. got boost, yours wasn't that bad. havent had another one like your car for a while now. jon, need your car on the 30th if I can pls.

best if I talk you through it. you have the buttons and diagrams to wire it? ring me on monday. I'm away at my parents until then (I'm on a 28k dialup link to my shop server right now.)

for those brisbane based I need TWO mules for the 30th of april. I have a 2003 car already - need a 2004.5 and a 2001. I'm trialling something and need to justify buying it BEFORE I lay a 4 figure sum of $$ down if you can help - ring/PM me.

yes.

he did- THANK YOU!!!!!!!!

was around that time I believe. will be at SCC08 as well. amanda, see what you started :blush: thanks guys! Andy65, ring me when you get a sec

prob late week. need the car for a full day.

I'll snap a pic of the one I know of. wasn't woodgrain. thing with it though - no SWC.

glad to be of service. mind if I use this in my feedback area (on the shop site but out of view.)?

NM35-31919 run that. have a really crap keyboard on my server.

run this VIN - factory momo wheel with airbag. NM35-31919 seee if there are SWC controls for it. the deviation on the cruise buttons is the radar cruise vs std.

whenever. coming week is fine if you are going past. pop it in the mail box

I do. 3342 - electric. van version is a pain on those cars.

I was after warrens ones. you could try that approach. I'm on decent terms with the SCS guys here in brisbane and that was my approach.