Jump to content
SAU Community

Recommended Posts

  • Replies 123
  • Created
  • Last Reply

Top Posters In This Topic

have you got pics of the kit installed.

i just want an idea of what the r32 gtst piping kit looks like and where the pipes run ?

how much for just a r32 gtst piping kit ?

cheers- Ricko.

Same question, need piping only.

Hey man,

the PM's your sending dont seem to be coming through :(

Could you please copy paste what u wrote and email it to me at : [email protected]

Would appreciate heaps!!

Cheers,

Dan.

hey mate, i would like to know this before i buy... is there any cutting required of the standard type m front bar on an r32 gtst and do i have to chop any of the fan blades or cut a hole in my chasis like the just jap cooler kits??? cheers mate

hey mate, i would like to know this before i buy... is there any cutting required of the standard type m front bar on an r32 gtst and do i have to chop any of the fan blades or cut a hole in my chasis like the just jap cooler kits??? cheers mate

you will need to chop the f**k out of the stock type-m r32 bar (i had to, and it needs tidying up atm). basically i found i had to cut a heap out of the centre hole including the vertical support bit, and completely cut out both the side holes in the bar.

i didnt have to chop the fan blades on mine. i just made sure the exhaust piping was pushed up against the cam cover and away from the radiator blades. you will need to cut a hole through the side part of the engine bay just below the battery compartment though.

the gts kit is very generic though, as it is made for r32/r33/r34. i found the support on one of the pipes was useless for my rb20det (the one that is sposed to bolt onto the engine block).

pm for pics if you want

Edited by flagger
3/ Hybrid RS spec kit (core - tube and fin - 580x295x95) - $730 delivered.

Got this in stock for JZA80 Supra?

Send me a PM or email. Ill gladly buy one of you. Thanks

PM sent.

:laugh:

couple of questions -

ok yep bar and plate or tube and fin?

fitment to a 97 stagea id IMAGINE is the same, being the same engine bay, same R33DET engine. anyone else know?

haha will await your PM.

  • 2 weeks later...
  • 2 weeks later...
1/ HDI GT spec kit (core - tube and fin - 600x300x76) - $630 delivered.

Will this fit an R33 S1?

Cheers

Jamie

Yep, will fit.

PM me ur email addy if you want a copy of the install guide.

:(

I would like the 'bar and plate' monster kit to suit r32 gtst. Can you supply me pics of the actual kit please!

I also need payment and delivery details.

Thanks.

Edited by HR-32
Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
    • This looks great! Awesome to have the 5 speed with an LSD in this. The Recaro's look like SR2's or SR3's. It's a shame they've been retrimmed as they would have looked sweet in their original colours. I think I'd want my agent to be a little more up front and informative too. I've never imported but I reckon it would make me a little nervous, so the more info the better.
    • Thanks for doing that Duncan! Makes you a good person in my books. We don't get kangaroos or wombats here. But we have bats and it's similar. AFAIK it's often the mums with a baby attached that get hit because they drop lower when starting from a tree. If you hit an animal, check on it. https://www.ifaw.org/au/resources/wildlife-rescue-app An app to get the closest wildlife rescue contact.
×
×
  • Create New...