Jump to content
SAU Community

Recommended Posts

cheapo lights are around $7.50 a bulb. Toothpaste is an abrasive so it makes sense that it would clean the plastic... I've heard it being used to polish other things too, but cant remember.

I polish my glasses with toothpaste once a month.

Sorry. I'll go now.

  • Replies 66
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

  • 1 year later...

I had some overspray on my headlight and cleaned it off with thinners.

What a farken mess! looked like wrinkly skin.

I tried cutting polish, that just made it shiny but didnt get rid of wrinkles and realised I'd really farked up. Tried Auotsol that worked but it was gunna take ages to get rid of all the wrinkles so I stepped up a notch and tried Gumption, that worked better but still a long way to go, until I used a 3m pad with the gumption. That worked really well, still took a while but only 1/2hr,but I to continually clean the pad because it built up with bits of plastic pretty quick. I then cleaned with water and spayed silicon spray on it and it came up a beaut.

If you look at my avitar you can see how farked it was.

DONT DO THIS UNLESS YOUR PLASTIC IS REALLY FARKED

  • 1 month later...
  • 4 months later...

Question, In order to remove the headlights, do i have to take off the front bar? If i do, the front bar for the r33 gts-t series 1 is just 3 screws at the grille, and 2 on each side under the fender right?

  • 4 weeks later...

I dont think u need to remove your bumper to take off the headlights. The actual headlight asembly is easy to take off from the car.

But no-one has answered the question of how to take off the front plastic cover from the headlight assembly. Can it be properly re-sealed? I have cleaned my light 100's of times with that polish from Unique Auto Sports and it is just a heap of crap. It works and looks good for a day or two then bang, yellow again!

  • 2 months later...

Putting your headlights into an oven to pull them apart is going to be risky.. especially if you've never done it before. When I got my R33 series II my headlights were (and still are) frosty looking because of the crap on the inside you just can't clean.

I did manage to find a place in Blacktown called Plastifusion and all they do is headlights. Link --> Plastifusion

They will do the hole oven business thing with your headlights, polish them up (inside and out) and re-seal them again. Unfortunately for me though one of my headlights has some fine cracking. In that condition they won't pull it apart to polish it. I basically need mine replaced :D

Anyone know of a place where I can source some cheap series II headlights? Nissan want $1000+ for a pair :P

There's also a place in Keysborough, Victoria that does change overs (is it Mr. Headlight??) Do a search on headlight +replacement, I read the thread 18-24 months ago...

any link? i broke the screw that adjust the level of the headlights, now they are pointing too high. thx

Could it be these guys?

Melbourne Headlight Exchange Pty Ltd

Unit 2/ 130 Bridge Rd Keysborough VIC 3173

ph: (03) 9706 3922 Auto Parts Recyclers

I couldn't find any website link for them.

When you guys clean the headlights, are you doing it with the lights still in the car, or are you guys actually removing the headlights and then doing it? I just dont want to get toothpaste or the maguires stuff on the paint??

how you going mate?

I just got my 33 back from insurance damage of some moron reversing into it.

The second hand lights put in by "Gold Coast Panel Works" on the gold coast, looked like they were brand new. And I mean brand new when i picked it up. If you bought a new car they would stack up.

They are based on the Gold coast qld. Im not sure how they made these lights from the wreckers look like this.

They are in southport give them a buzz

I guess alot of ppl might have this problem if your line is year 94 and below.Mine's a 93 and the headlights getting a bit yellowish.Just wondering how to make it white and shiny(like big red) again.

thanks

If its just the outside(I thought it was on the inside because tried lots of different things and didnt change) MR Sheen no s**t! took it right off and thats without removing the lights

Edited by BOVed

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
×
×
  • Create New...