Jump to content
SAU Community

Recommended Posts

I went to APC the other day and i saw a RB25DE plenum which looked very similar to the greddy item. It apparently uses the standard injectors and a Q45 throttle body but is a cheap casting job.

Has anyone actually had one of these fitted with good results?

I ask because i have a crappy cut and shut with a front feeding (like GTR) inlet and i would like to replace it with this one if it is any good. I believe they said it costs around $700ish.

Link to comment
https://www.sau.com.au/forums/topic/103450-rb25-intake-plenum/
Share on other sites

  • Replies 40
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

I checked out ISL-33P  and his profile says a custom plenum (exchange) costs $1000 where the one i am talking about costs $700ish (from memory).

Where is APC, i would love to see some pics of the cast one.

Also paulr33, i need a front facing plenum like the greddy one for a 25/30 engine conversion so i dont have to lower the motor to far and can keep my strut bar.

i have a 25/30 and for 1300 ariel (ISL33P) created a custom plenum that flows a shitloads more than most top jap brands (has flow tests to prove and also comes with 80mm throttle body and bolts to stock runners and fuel rail

ben...

ill get pics of the inside tomorrow to try and show how its pretty much full smooth theres no weld marks inside, no rough surface at all, and has been bench flow tested with less than 2% change within all 6 cylinders which i have recently seen a greddy one bench flow tested and it aint even close to that

ben...

  • 2 weeks later...

Plazmaman Plenums are the best i have seen when looking to purchase a plenum. it works great and looks really good. They make em in some awesome 80tonne press.

go to www.gtr.com.au and have a look there (UAS) $1150

They are easy to install and use the stock throttle body (or you get another flange for any other type) and they use the standard gasket and runners.

Makes me engine bay look sweet and with the RB30DET i can fit my strut brace =)

skyplazplenum.jpg

skyplazplenum2.jpg

They have been flow tested and proven to make power as well.

DYNO SHEET BELOW SHOWS RESULTS OF THIS PLAZMAMAN PLENUM & INTERCOOLER KIT FITTED TO A SKYLINE R33 GTS-T WITH STANDARD TURBO, STANDARD ECU (WITH FUEL CUT DEFENDER), STANDARD ENGINE INTERNALS, ADJUSTABLE EXHAUST CAM GEAR, RAM POD AND FULL 3" EXHAUST SYSTEM.

plazmadu.gif

Edited by Guilt-Toy

This is what the one from APC looks like.

The difference is that this looks like it is meant to be there and it is apparently identical to the GREDDY manifold but takes the standard injectors (not standard throttle body).

post-2060-1139455220.jpg

Edited by R33NT

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Cheers. Skyline is back on the menu, can’t get rid of it. It’s like a child you don’t want, or herpes 
    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
×
×
  • Create New...