Jump to content
SAU Community

Recommended Posts

that means your tyres need replacing.

i ran 330rwkw and had little traction issues using street 225's.

skated a tad @ the top end of each gear. Otherwise in my book it was nothing.

I've seen poorly setup stock R33's get more wheelspin.

all in suspension and tyres.

As for your question about torque... i doubt many here have had thier motor on an engine dyno to be able to accurately answer that.

Dynos are a tuning tool... worse if you try using the torque figures

What does the R31 have leaf springs??? LOL

  • Replies 47
  • Created
  • Last Reply

Top Posters In This Topic

good post

im about 200rwkw, and its probably too much for just a street car

just a quick blip and you are pretty much over the speed limit

theres not many roads around where u can enjoy the power without exceeding the speed limit

id love to make more power if i hit the track, but as my line is our daily driver and it needs to be on the road, it probably will never happen

i wont be powering her up anymore i dont think

This is why I went the 3ltr... Improve that 0-speed limit acceleration by minimising lag and increasing low engine speed torque.

Idling up off the line the 3ltr really does haul arse with the skylines low diff ratio's.

Idling and simply popping the clutch with wot will have it accelerating off the line quicker than the usual LS1 V8, the V8's tend to bog down and lag a little before reving up.

LS2's its around par on as they do seem to ave quite a bit more of a lunge at low rpm.

My uncle has a 250i 6speed LS1 that really does feel rather gutless at low rpm compared to mine.

a track car obviously means a high revving 2.7 -> 3.0 with large twins ?

Even then, on slower tracks, it will most likely get munched.

i just meant a car that is only used on the track.

for a perfect street car i think u will need round 280-300rwkw. i have 260 at the moment and it feels a little slow after a while. definately going to upgrade to something bigger

You guys are all crazy...:(

Ok, i owuld love a GT3 Porka as a street car. It would be lucky to have 250kws at the wheels!

Even with 200rwkws you cant even rev out 3rd gear...If its a street car, the more power you have the sooner you will find yourself in a world of trouble ...which is no fun.

If you use your car for somethin other thenA-B day to day driving, lol the more power the better :P

my vl had rb25, t70, plenum, microtech, fuel system, gate etc etc....

270rwkw on 13psi in a 1300kg car was scary, but it still wasnt enough ;)

enough to light up the rears at over 100kmph but still not enough.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Lets say I wanted to buy this, specifically for this purpose. How do I actually perform the function. Can I still buy a Consult-1? Am I about to be burned by the fact my car is a 2000 model Series 2 R34 and thus will be some stupid other system? Do I just need this -> https://obd2australia.com.au/product/nissan-consult-14-pin-to-usb-ddl-diagnostic-interface-with-ftdi-ft232r-chip/ And with what software?
    • That's probably OK. That's a face to face compression joint between two surfaces with the clamping load provided by those bolts. So.... it's unlikely that the bolts will end up feeling that load in shear, unless the clamping surfaces are not large enough, bolts not got enough tension on them, etc etc to prevent the two faces from moving wrt each other. Which... I would hope the designers have considered, seeing as it's probably one of the most important things the upright has to do apart from resist collapsing in its own right. But yes, it would definitely be worth asking them what their safety factor on that part of the design was. I tend to think that the casting, being a casting, is not necessarily the strongest bit of material in the world. It's about an inch square, and when you think about the loads that are being put into it, you have to wonder what safety factor the Nissan boys (and every other OEM engineer who has designed all the millions of other uprights that look essentially the same) used to account for defective casting, aging, severe impacts on the wheel, etc etc. 
    • Those bolts would be orders of magnitude stronger that cast aluminium though.  And its mainly clamping force, not shear they are dealing with?
    • Except all that twisting force that is breaking a cast piece, appears to be going through 4 bolts in the picture Johnny posted of the BryPar one...
    • The smart approach is to use the gearbox loom from the manual car. Makes it a lot easier - just plugs into the switches on the box and plugs into the main loom up near the fusebox. Then you only need to deal with bypassing the inhibit switch. The other approach requires you to use the wiring diagram to identify those wires by colour and location, perhaps even indulging in a little multimeter action to trace them end to end to make sure, and then.... you will have the answers you need. The R34 wiring diagram is available on-line (no, I do not have a link to it myself - I would have to do a search if I wasn't able to go to the copy I have at home).
×
×
  • Create New...