Jump to content
SAU Community

Recommended Posts

  • Replies 286
  • Created
  • Last Reply

Top Posters In This Topic

thanks for the heads up on the plate, ( proengins)

well had a go at making a wedge, first attempt nearly lost my finger, with the grinder.

but got there in the end, god 2mm one side 10mm the other side then drill out the center to fit over the thread.

but all on now and straight, all gaps the same to water pump studs 4mm, so well chuffed.

piccy

003.jpg

002.jpg

001-1.jpg

  • 2 weeks later...

you cant use any other engine mount dave, because as it is there's 2 parts of fook all clearance between the bottom of the diff and the cross member. i posted a pic in here somewhere showing how close it sits

so, rd28 engine mounts solve the bonnet clearance issue? or is there something else? ive tried reading it all but no definative answer.

if u are enquiring about an rb30 in a gtr, u need to use the same mounts. u can slot the mount holes but not recommended due to lack of clearance

  • 2 weeks later...
  • 3 weeks later...
lol i gain an extra 200kg (stagea) over a gtr but my bonnet shuts without an issue with covers on and twin turbo pipe on :D I'd still rather lose 200kg and need less power lol.

I have been thinking about running twin gtrs turbos now instead of -5s, i think they are -10s from memory? I remember someone on here runs them on a 30 setup and wondering what the drivability is like? i want around 500hp at wheels mark on 18-20psi. Im running a freshened bottom end but still stock rods and duratech cast pistons, so still around the 8:1 comp ratio. I dont care if the thing blows to bits i wanna see how long it will last :down: My head is stock 26 with no port work and stock cams at the moment which wont help either, but bolt in cams are always a future option.

Ive got GTRS's, i want to swap them for dash 5's in the next month or so.

What rear does your set have?

Drivability is pretty much perfect as Marko said. Only things id change are turbos and cams

ok cool. just gotta figure out how im going to fit my s372r borg warner turbo in there...

Harden up mate, iraqi sand dune nissan patrol racer style right out the bonnet level with the roofline :laugh:

  • 1 month later...

Maybe someone get shed some light on my current set-up and the issues I am having...

Im running a built RB30 bottom end with standard 25 vct head. The old set-up was running a GT3082r (0.82r) with 6 boost and supporting mods and made 280rwkw @ 17psi. This is through a built 5speed auto, fully manualised with 4500rpm stall.

I then changed to a GT35R with the same mods. On 11psi, the car made 246rwkw @ 7100rpm. We then upped the boost to 18psi, however the car only went 260rwkw and stopped making power after 6000rpm (sharply).

Any ideas what this could be? A few people have mentioned valve float but I also dont know how to verify this.

What size rear housing on the 35R and what size exhaust? cat? sounds like a restriction..

.82r ... its the exact same housing as the older 30R but just machined out to fit the larger exhaust wheel. No cat, just a muffle towards the end of the system (being a 3" mandrel).

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • What about if you just give it direct 12v and earth?
    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
×
×
  • Create New...