Jump to content
SAU Community

Recommended Posts

It will be near impossible to remove it completely. I rented a place before with a really stuffed up driveway. Everytime I drove up the driveway, my inside wheel would spin. After about 8 months, there was a pretty thick tyre track on the ground.

We tried petrol, kero, turps, everything. We tried scrubbing it with the chemicals mentioned above. We tried applying the above chemicals, then lighting them on fire. We tried using a gas cylinder as a flamer to try and burn it off.

While all these made it better, it was still quick noticeable.

Just paint over it and be done with it.

yeah ive had the same problem at a place i rented ages ago. i found using a wire brush and a heap of washing powder (nappy san or similar). Have ya tried a pressue washer/gurney, or HCL over the marks, if that doesnt work then ur probally screwed. ;)

god. i read you post and i PMSL ;)

anyhoo citroclean is agressive as. it removes polish off the floor so it should make a dent in it at least. try a few application of it to remove it. ie put it on and attack with a stiff brush, wait a little then put more on and attack it again.

anyone tried CLR?

if all else fails buy some grey paint lol

Your local auto parts supplier should have a range of concrete cleaning products.

I used one a while ago, very caustic stuff, did a good job of removing oil stains, but I don't know how it would go with rubber. (I guess essentially they're the same compound?)

Hose the area, dump the powder on, scrub it, let it sit a bit, then hose it off.

But if you're going to use anything like that, suit up well.. it burned little pitted holes into my leather work boots.

I used one a while ago, very caustic stuff, did a good job of removing oil stains, but I don't know how it would go with rubber. (I guess essentially they're the same compound?)

Theoretically yeah, they're both hydrocarbons. Which means they should both react (to a certain extent) to other hydrocarbons, especially volatile liquid ones (kerosene or petroleum solvents).

I still pity the fool that shits in his own backyard.

I still pity the fool that shits in his own backyard.

God invented rental properties so that people could shit in their own backyard, then move along to the next place when the shit can is full :D

Be mindful with whatever you're using that it's possible that anything that would dissolve the rubber by making it softer is likely to sink into the concrete (especially if it's really porous).

Obviously if whatever you're using eats all of it away that's fine, but sometimes chemicals tend to do a half assed job.

alternatively... soak your tyres in diesel, then proceed to drive up and down the driveway evenly.

then give the landlord a bill for treating the driveway with waterproofing silicone.

i used to work at Golden Circle, and they got this stuff that'll burn the skin clean off your hands...

wen u squeeze the peel of an orange u get this acidic juice... they process the stuff into wat Golden Circle call "citrus oil"

if you can find that, u got no worries

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, hard to find and a pain in the ass to change with the transverse engine. I’ve worked on a GTiR before and it’s not a job I’d ever want to do again. theres a company in South Africa that makes RS3 gearbox adaptors for the AWD SR20 including gearbox mounts, so I could modernise it and go a dual clutch with paddles. For now tho, it ticks all the boxes. Super cheap, can throw the kids and their junk in the back, and SR20 that I can turbo cheaply, a CVT that’s not a dog’s breakfast like the V35, and has 80% interchangeable parts with stuff I can source from the wreckers cheaply…. But it’s still unique. I love the wagon back of the Autech version. It’s cheap enough that I can buy another stock manual FWD Primera with SR20VE, swap the gearbox to the N15 pulsar short gear ratio box, swap out the brakes to the R32 ones I pulled off my 32, register it on club plates and take it racing. $1300 shipping from NZ. Heaps of parts and aftermarket builders for transverse SR20’s in NZ.
    • Hard to say, just pop the rocker covers off and have a look if you think it's cammed. You probably need to replace the valve cover gasket/half moons anyways.
    • From my youth: GTi-R clutch change is a massive pain. The gearboxes are fragile? But the car is super cool and I want one 😢 
    • Remember this is 1988 tech.
    • Driveline vibration is resolved. I ended up loosening all my engine mount and trans mount bolts, giving it a good shake then retightening everything and it's gone... Let's just say I was surprised that fixed it.  I've been happily driving it around again but unfortunately put zero time into my direct port/constant pressure WMI setup. I'm on vacation next week, so I'll try and finalize it then.  On a different note, I spent all week fuel/ignition mapping 2x 216L V16 engines. Turbo's were burning glycol and we swapped them out for larger units. We also had planned emissions testing on site, so I figured I'd be there the same week to use their instrumentation and massage any emissions issues out if needed. This was a first for me. Fuel management is similar in certain ways to automotive (i.e air density as load variable) but very different in others. It's all PLC based and AFR's are controlled by air and not fuel. They use a control valve between the turbo and air manifold to control pressure which in turn controls AFR's. Due to this, target AFR tables supplied by the OEM are in pressures and not mass which really through me off. They use air pressure vs fuel pressure tables. I also relied on an O2 concentration sensor the emissions team had in the exhaust. Ignition timing was also all over the place and we were losing a fair bit of power. They're now happily sitting at 16-40BTDC depending on load. We were making about 1600kw at 900rpm at 90% load. Engines were running a lot smoother as well.    
×
×
  • Create New...