Jump to content
SAU Community

Recommended Posts

i didnt think they were legal but reading the new motor magazine states that they are, definatley gonna find out for sure since i have them and wanna know 100%... mine a so secure feels so safe, i guess if they rattle then they would be defected for but secure ones i cant see whats wrong

i cant see why the flush mounted ones would be additional hazard to pedestrians... maybe the ones with the wire over the front or the ones that stick up... maybe try checking in your state... like everything else the laws owuld vary from state to state... just ring you local rta they will tell you...

I was in that position with a Bluebird that had a much modified rad support panel (foreigh R32 rad and hooge IC) . The answer was to fit a plunger (or as suggested to me dog cock !) style catch from a Datsun 1600 . It works well but the fabrication to fit it to the bonnet is involved and may damage its paintwork .

Cheers A .

They are Legal in Canada :P

and for the ones that rattle.... they were probably cheep ones... get them from a good Canadian or Japanese manufacturer :P

Edited by James Mramor

I thought they were illegal for pedestrian safety too.

Anywya, for pins that rattle they aren't tight enough. Either crank the pins down or add to the support between the bonnet and the chasis

  • 7 months later...

I have the larger ones on mine, with a latch, illegal in the ACT, wouldn't mind swapping them for the smaller ones. or putting blanks on the bonnet, as it looks bad atm with holes in the bonnet :O, anyone know if thats legal?

Can't comment on the legality of "bonnet pins" however i would see a car manufactures badge that protrudes the bonnet to be more of a pedestrian risk then a bonnet pin, but this is common sence therefore, it's probably the case that the pins are illegal in NSW. If they are, i'd just go flush mounted ones like someone already sujested.

I think it depends on the type of bonnet pin some cars come with them standard one that springs to mind are the old gt falcons which had flush fitting bonnet pins no protrusion above bonnet line so id say pins that protude above the bonnet line would become a problem for pedestrians i.e cause more damage to them .So if fitting bonnet pins try for something flush mounting

Cheers Peter

  • 2 weeks later...

bonnets are meant to crumple when you hit a pedestrian or crash, this makes it safer for you and the pedestrian. if the bonnet doesnt crumple it can go straight through your windscreen and take your head off. bonnet pins would probably be illegal because they'd prevent the bonnet crumpling properly.

This was argument a cop had with me regarding lifting the back of the bonnet up two inches for enhanced cooling away from the rear internal clips, but I cant see how pins would be a problem as they would retain the bonnet to the frame better.

The pedestrian damage issue would be the main reason, if in fact it is illegal.

Then again if it's a :-

Skyline = Illegal

Falcodore = Illegal

EuroWeapon =Legal :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • https://www.facebook.com/share/p/18rmVb1SKB/ 
    • The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...