Jump to content
SAU Community

Recommended Posts

  • Replies 297
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

just get them hpc coated...come out nice and silvery...cheap and wont chip or scratch off as easily as paint. ive seen a ca18det and rb25 covers done. Around 40 bux to do a set of covers.

  • 1 month later...

hay man just wondering i have an r33 gtst and what do you need befor you take off the rocker covers is there any gaskets or seals you need to replace when you take the covers off and paint cos i want to paint mine the same colour as the car (marone)

prety easy.. i didnt take the fuel rail or any of the stuff on the intake side off..

just loosened it and pushed it to the side so i could get the back bolts undone... once they were loose i used a magnetic stick to pull them out, exhaust side is easy

  • 2 weeks later...

so what went wrong?

I'm going to do mine next week, any advice???

I have bought some primer but havent choosen the paint yet! I can't settle on a colour....

they might just go back on black!!! hmmmm

toss up between Nur gold and R34 metalic red....

so any tips would be great!!!

make sure you clean the surface with metho or something that doesnt leave any resedue.. like electrical contact cleaner.

again clean the surface after primer before you paint.. sand the primer back and apply more primer till its heaps smooth.. then wet and dry it, then clean n paint

Mark,

I think the plenum is a wayyyyy to hard a job! I simply masked it up in place and found a similar black spray to touch up the few chips I had in the original paint... and it turned out good!

as for the cam covers! I am getting pissed with it, as the surface just isnt coming up all that flash!

I am about to give in, and go get the crinkle finish paint (like the red cover on the S1 R34 GTR above) and go with that, as it hides the imperfections far better!!!

and what he was talking about was the plastic fuel wiring loom cover (allen key) undo and push it away...

I also found the twin turbo pipe had to come off too...

if this doesnt work, I will admit failure and get a professional to do it in the future!

grrrr

Mark,

I think the plenum is a wayyyyy to hard a job! I simply masked it up in place and found a similar black spray to touch up the few chips I had in the original paint... and it turned out good!

Hrmmmm. Cheers Ben. Mine has pretty much lost all the paint (bizarre for a *genuine* 70,000km car :) ) so it'll have to come off, because I'm going to bake the parts to cure the paint.

I shall see how I go.... (famous last words....) :)

Drew was it fairly easy to remove the plenum? Or is that what you were talking about when you said just loosen everything?

i dont think taking the plenum off just to paint it is worth the blood sweat and tears.

i just did mine because i have the enging out

And Sean some of that painting you've done looks very intricate! Did you freehand or mask? Parts like around "Nissan" and RB26 look very nice!

Cheers. I did it free hand with a fine brush and model paint.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Cheers. Skyline is back on the menu, can’t get rid of it. It’s like a child you don’t want, or herpes 
    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
×
×
  • Create New...