Jump to content
SAU Community

Recommended Posts

So theoretically it would actually be best to have the sump breather go back into the cam covers, which would help push oil down the head drains if it has that external passage.

But by that logic the breathers at the back of the block are pretty massive and there are two... So the oil drains shouldn't have that much trouble draining..... Theoretically.

No it doesn't help in the way you've described because the sump itself is where the blowby goes and where the "high" pressure is. The idea is to reduce the blowby gasses that have to go through the head - either by directing them to the catch can or around the head into the breather system (via the filler cap mod). I favour the former simply because it reduce the velocity of the gasses in the breather system and therefore makes it less likely they will entrain oil. Also you don't want the whole system pressurised as it just costs you horsepowahs.

In a wet sump the only thing returning oil to the sump is gravity and the oil has to pass the blowby gasses going in the opposite direction.

I'm trying to upload a pic of my bay but it won't let me :(

Menthol,

It's not that it will push oil down but reduces how much air is flowing up the returns trapping the oil in the head, people under estimate how much blowby come out of these things under high boost applications,ie 20psi+, next time your car is on the dyno see if you can watch the breather outlet, it will shock you

Simon,

While it will greatly reduce the amount of air pressure is the crankcase, air will flow the path of least resistance and if that is via the two lines running to the catch can then that is where the air will flow and it will take the oil with it, if the catch creates a restriction then it will leave via the oil returns again trapped the oil in the head

I have seen too many times setups running from to low in the crank case ( mine included which come from the block ) where the lines leave without passing through the cam covers and they end up filling up the catch can leaving the sump with out enough oil :(

If the pickup is to low then around a high speed high power corner the oil will cover the pickup and the blowby will pump the oil up the line to the catch can, but if you are not having issues with yours then you obviously have it sorted :thumbsup:, if it aren't broke don't fix it :)

Another way to increase vacuum in the crankcase and rocker breathers is to also run a large diameter line from the catch can to the intake pipe. This will induce a lower then Atmospheric pressure AND it allows you to run a sealed catch can and make it more legal if you choose to do so...

Down side is if you choose to seal the catch can there may get oil in the intake

Another way to increase vacuum in the crankcase and rocker breathers is to also run a large diameter line from the catch can to the intake pipe. This will induce a lower then Atmospheric pressure AND it allows you to run a sealed catch can and make it more legal if you choose to do so...

Down side is if you choose to seal the catch can there may get oil in the intake

What you are describing is the stock setup for the GTR's with a Nismo can fitted.

Another way to increase vacuum in the crankcase and rocker breathers is to also run a large diameter line from the catch can to the intake pipe. This will induce a lower then Atmospheric pressure AND it allows you to run a sealed catch can and make it more legal if you choose to do so...

Down side is if you choose to seal the catch can there may get oil in the intake

In theory that's sounds good but what it does is increase air velocity up the oil returns/catch can lines increasing the amount of oil leaving the engine, and is how my setup is currently done for legal reasons and why so much thought had to go into it and it's proven to work with 22psi boost and 400kws at all 4 on SMSP-s which is a tight twisty track that does a good job of showing a setups short comings

Do you have an oil return line from your catch can to the sump mick?

If it was draining back when the engine is in vacuum that would be a solution?

Yeah, -12 line from bottom back of front catch can to fitting in block next to starter motor with a one way valve on it

It can't until engine is off as the vacuum is running through the catch cans

I'm trying to upload a pic of my bay but it won't let me :(

Menthol,

It's not that it will push oil down but reduces how much air is flowing up the returns trapping the oil in the head, people under estimate how much blowby come out of these things under high boost applications,ie 20psi+, next time your car is on the dyno see if you can watch the breather outlet, it will shock you

Simon,

While it will greatly reduce the amount of air pressure is the crankcase, air will flow the path of least resistance and if that is via the two lines running to the catch can then that is where the air will flow and it will take the oil with it, if the catch creates a restriction then it will leave via the oil returns again trapped the oil in the head

I have seen too many times setups running from to low in the crank case ( mine included which come from the block ) where the lines leave without passing through the cam covers and they end up filling up the catch can leaving the sump with out enough oil :(

If the pickup is to low then around a high speed high power corner the oil will cover the pickup and the blowby will pump the oil up the line to the catch can, but if you are not having issues with yours then you obviously have it sorted :thumbsup:, if it aren't broke don't fix it :)

yeah exactly what happened to me, Did you just bore a hole in your crank and weld -12s into that?

i was thinking about doing this but was worried about the strength in the block walls.

if this can be done it would save me alot of headache

yeah surely not the best :/ I have 2x -12 on the highest point of my sump, and iv only had the issue of puking when I over fill my sump.

seeing as I run e85 I don't drain mine back to sump either

would be interesting to know how else you could get the vents higher.

next time ill just go drysump, LESS HASTLE!!

Hardly less hassle but certainly as better solution if you have money to burn. I have managed without but if I had a 600kw build I would at least look at an accusump If not a full dry sump.

I drilled and tapped 3 holes in the block ( 2 x -12 and 1x -16 ), placement of these holes is very important for block strength, get it wrong and shit can turn bad pretty quick

I also have the water jackets half full of grout and a platinum racing adaptor plate which ties the girdle and block together

The Accusump is a really really good band aid, but and ounce of prevention is worth a pound of cure, set your oiling system up right from the get go and it shouldn't be necessary

  • Like 1

I have a 600hp 25/30 driftcar, about to turn it up a bit for racewars next yr, hoping to go 800rwhp, but on current set up its running 6.5L trapdoor extended sump, 2L accusump, 2 sump breathers. 2x1.2mm restrictors, blocked vct feed, enlarged oil drains, decent vented catch can. tomei oil pump. all up with the oil cooler and accusump it holds around 9.5L. the only time ive ever had quite an oil puke was when I over filled the sump, other than that, its usually pretty clean apart from the ethanol. has quite a high oil pressure too, sits around 80psi once warm at 2000rpm hits relief spring pressure (110psi) around 4000rpm. haven't had any issues.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...