Jump to content
SAU Community

Whiteline Rear Camber Kit

Col-GTSX
 Share

Recommended Posts

Col-GTSX Grand Master

Col-GTSX

Posted
Posted

This kit suits;

R32/33/34 Skyline GTR/GTS-T/GTS (1990-2003)

300ZX (89-95)

200sx S14-15 (94-03)

180sx S13 (89-94)

RRP in stores $199ea

This kit is all you need to adjust your rear suspension + or - 0.75 degres.

The kit includes new bushes and both top and bottom bolts for left and right of the car.

If you require more adjustment all you need is another kit (which i have)... So if you use 2 of these kits you will achieve 1.5 degres of adjustment. Please note that you will require a wheel alignment once fitted to setup correctlly to ensure maxium tyre contact without scrubbing...

Most people use these kits to fit 255mm+ sized tyres under the rear guards and keep it legal. It also makes it look so cool from behind. Makes the car look very serious.

PRICE: $110ea

(inc Express postage to anywhere in Aust)

Please refer to www.whiteline.com.au and download their full catalogue to check vechicle suitability.

Thank You

post-2979-1145088950.jpg

Link to comment
https://www.sau.com.au/forums/topic/113647-whiteline-rear-camber-kit/
Share on other sites
Col-GTSX Grand Master

Col-GTSX

Posted
  • Author
Posted
Will you take $100 inc post for 1 set?

No... Trade price at repco is $148 inc GST each... (I have a reciept)

U have PM...

Pm returned

So to clarify, you can fit the 2 together for a maximum 1.5 degree's adjustment?

How difficult is it to adjust?

Thanks,

C

Yeah mate you can use up to 2 kits at the same time. Adjustment is best left once the car is on a wheel allignment jig to get accurate results. 2 kits will yeild a max of 1.5 degrees

is it brand new and unused etc?

are those pineapples in there? bit hard to make it all out in the pic...

Brand new yes... No pineapples... They are the nessary rubbers to replace while your there doing the camber adjustment... I guess whiteline assumed people would replace them while they are doing this job.

Col-GTSX Grand Master

Col-GTSX

Posted
  • Author
Posted

One set confirmed as Sold and waiting on payment from 'djr81'

Other set is held atm, waiting for reply of pm for 'ant95GTR'

If second set falls through 'Adam 33' is next in line to take a unit...

djr81 Grand Master

djr81

Posted
Posted (edited)

Col,

Paid for.

Just by the by - to answer some queries you use them on the rear upper arms to allow sufficient adjustment and allow you to add sufficient postive camber to compensate for the -ve camber that happens when you lower the rear ride height on a GT-R. Just be careful that you read the instructions carefully as the drawing shows two top arms, not a top and a bottom arm which is what it looks like at first glance.....

Cheers

Richard

Edited by djr81

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • nash47
      Cas issue

      By nash47 · Posted

      Did and sync timing with light 
    • MBS206
      Cas issue

      By MBS206 · Posted

      Have you done the Ignition Sync Wizard in the AEM software?
    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • MBS206
      RB25DE NEO with Haltech ECU

      By MBS206 · Posted

      You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
×
×
  • Create New...