Jump to content
SAU Community

Recommended Posts

This kit suits;

R32/33/34 Skyline GTR/GTS-T/GTS (1990-2003)

300ZX (89-95)

200sx S14-15 (94-03)

180sx S13 (89-94)

RRP in stores $199ea

This kit is all you need to adjust your rear suspension + or - 0.75 degres.

The kit includes new bushes and both top and bottom bolts for left and right of the car.

If you require more adjustment all you need is another kit (which i have)... So if you use 2 of these kits you will achieve 1.5 degres of adjustment. Please note that you will require a wheel alignment once fitted to setup correctlly to ensure maxium tyre contact without scrubbing...

Most people use these kits to fit 255mm+ sized tyres under the rear guards and keep it legal. It also makes it look so cool from behind. Makes the car look very serious.

PRICE: $110ea

(inc Express postage to anywhere in Aust)

Please refer to www.whiteline.com.au and download their full catalogue to check vechicle suitability.

Thank You

post-2979-1145088950.jpg

Link to comment
https://www.sau.com.au/forums/topic/113647-whiteline-rear-camber-kit/
Share on other sites

Will you take $100 inc post for 1 set?

No... Trade price at repco is $148 inc GST each... (I have a reciept)

U have PM...

Pm returned

So to clarify, you can fit the 2 together for a maximum 1.5 degree's adjustment?

How difficult is it to adjust?

Thanks,

C

Yeah mate you can use up to 2 kits at the same time. Adjustment is best left once the car is on a wheel allignment jig to get accurate results. 2 kits will yeild a max of 1.5 degrees

is it brand new and unused etc?

are those pineapples in there? bit hard to make it all out in the pic...

Brand new yes... No pineapples... They are the nessary rubbers to replace while your there doing the camber adjustment... I guess whiteline assumed people would replace them while they are doing this job.

One set confirmed as Sold and waiting on payment from 'djr81'

Other set is held atm, waiting for reply of pm for 'ant95GTR'

If second set falls through 'Adam 33' is next in line to take a unit...

Col,

Paid for.

Just by the by - to answer some queries you use them on the rear upper arms to allow sufficient adjustment and allow you to add sufficient postive camber to compensate for the -ve camber that happens when you lower the rear ride height on a GT-R. Just be careful that you read the instructions carefully as the drawing shows two top arms, not a top and a bottom arm which is what it looks like at first glance.....

Cheers

Richard

Edited by djr81

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Stock ECU (or more accurately stock tune) absolutely refuses to go over 10psi and behaves like you have seen. The Nistune is the same if it is the stock tune. If the Nistune chip has been tuned, the resulting tune could be literally anything for any combination of parts. The Nistune just makes the stock ECU Tunable.
    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
×
×
  • Create New...