Jump to content
SAU Community

Recommended Posts

my mate will spray it free and ill fit it so a bonus there :D

if that is with the bottom lip its probably not too bad a price, i want the one identical to yours with the holes, any idea of the vin number of a car that came with one standard?

Edited by 2630GTS

Those holes are N1 vents. To get a genuine GTR N1 front bar costs a packet and they are rarer than you can imagine, and Nissan will not sell you one. The genuine vents are worth like $300+ (just for the vents) but few people have real ones. Mock ones can be found starting about $50 on ebay etc.. A genuine GTR fr bar will not have indents for the slots at all so you would have to cut them out... not sumthing you want to get wrong!

There are comapnies that make fakes for like $550 they have indents, so you can pop them out and buy some vents to put in there so thats about $600 before paint and fitment..

im pretty sure it is a nismo option rather than only fitted to n1 32gtr's, they are simply too common on gtr's. im sure many owners could confirm this.

ill give nissan a call tomorrow cheers :D

You could option them from nissan when buying the GTR also, but the vents are called N1 vents. The genuine vents themselves are worth HEAPS. And I promise you Nissan will not be able to help you with them. Mine are fake, 32line's are too, another friend I know had them and they were fake. They are common because a lot of people get the fake ones.

Hey Rekin nice rims I am keen on these from Just Jap, what size and offset are they?

Thanks :thumbsup:

17x8 +30

17x9 +30

I might have some troubles lowering the car as the rears stick out a fair bit. Dont think its an issue with the GTR's but :huh:

Are you sure the guards will need to be flared?

Ive got 19 x 9.5 with 265 rubber on the rear. Apart from the guards being rolled, I certainly dont have them flared..

Got a couple of cool photos ;)

DSC02411.jpg

DSC02406.jpg

DSC02524.jpg

Edited by Yidz
I've got the same wheels, same size and lowered.. so U need to roll and flare the rear guards

DSCN2547.jpg

Cheers

rolling i can deal with, but not really keen on flarring..

Can you post a pic of a closer look at the flarring?

Also how low is your car from centre to wheel arch?

I think my shocks will drop the height to 340mm and hope i wont need to flare..

Thanks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...